4
E33 FPI Direct Vent Gas Insert
SAFETY LABEL
This is a copy of the labels that accompany each
E33 Gas Insert. We have printed a copy of the
contents here for your review. The safety label
is located on a plate inside the base of the unit
visible when the bottom louver is opened. Ensure
that the safety label is attached to the unit.
NOTE: FPI units are constantly being
improved. Check the label on the unit and
if there is a difference, the label on the unit
is the correct one.
Fan Part No. 910-331/P
Electrical Supply: 115 V, 56 WATTS, 60 Hz
Side Walls
*A 8"
(203mm)
Ceiling
B
47"
(1194mm)
Min. Mantel Height
C
15"
(381mm)
Max. Mantel Depth
D
3½"
(89mm)
NOT FOR USE WITH SOLID FUEL
Minimum Clearances to Combustibles from Insert
VENTED GAS FIREPLACE HEATER
For Manufactured Home Installation: This Direct Vent System Appliance must be
installed in accordance with the manufacturer's installation instructions and
Manufactured Home Construction and Safety Standard Title 24 CFR, Part 3280, or the
current Standard for Fire Safety Criteria for Manufactured Home Installation, Sites, and
Communities ANSI/NFPA 501A, and with CAN/CSA Z240 MH Mobile Home Standard in
Canada.
This appliance is only for use with the type of gas indicated on the rating plate. See
owner's manual for details. This appliance is not convertible for use with other gases,
unless a certified kit is used.
This fireplace has been converted for use with a gas fireplace insert only
and cannot be used for burning wood or solid fuels unless all original parts have been
replaced, and the fireplace re-approved by the authority having jurisdiction. For use with
glass doors certified with the appliance only.
WARNING:
For installation in Solid Fuel Burning Fireplaces. This appliance must be installed in
accordance with local codes, if any. If none, follow the National Fuel Code, ANSI
Z223.1/NFPA 54 or Natural Gas and Propane Installation Codes, CSA B149.1. This
vented gas fireplace heater is not for use with air filters.
DO NOT REMOVE THIS LABEL / NE PAS ENLEVER CETTE ETIQUETTE
Listed: VENTED GAS FIREPLACE HEATER
Tested to: ANSI Z21.88b-2003/
CAN/CGA-2.17-M91
Certified for / Certifiée pour: CANADA AND U.S.A.
REPORT number 303530
CSA 2.33b-2003,
Serial No. / No de serie
298
`
NATURAL GAS FIREPLACE INSERT:
MODEL E33-NG1
Factory Equipped For Altitude 0-4500ft. (0-1370m)
Min. Supply Pressure
5“
WC
(1.25 kpa)
Low Setting Man. Pressure
1.1"
WC
(0.27 kpa)
Max. Manifold Pressure
3.8"
WC
(0.95 kpa)
Orifice Size
31
DMS
Minimum Input
20,000
Btu/h
(5.86
)
Maximum Input
38,000
Btu/h
(11.13 kW)
kW
D
E
F
H
G
A
B
C
Model/Modele:
E33-NG1
Model/Modele:
E33-LP1
918-491
PROPANE GAS FIREPLACE INSERT
: MODEL E33-LP1
Factory Equipped For Altitude 0-4500ft. (0-1370m)
Min. Supply Pressure
12"
WC
(2.99 kpa)
Low Setting Man. Pressure
2.9"
WC
(0.72 kpa)
Max. Manifold Pressure
11"
WC
(2.74 kpa)
Orifice Size
5 0
DMS
Minimum Input
19,000
Btu/h (5.56 kW)
Maximum Input
35,500
Btu/h (10.4 kW)
Alcove Width
E
76"
(1930mm)
Alcove Depth
F
36"
(914mm)
Hearth Height
G
1-1/4"
(32mm)
Hearth Depth
I
13"
(330mm)
Non-Combustible Hearth Extension
Hearth Width
H
45-1/2"
(1156mm)
FPI Fireplace Products International Ltd., Delta BC, CANADA
MADE IN CANADA / FABRIQUE AU CANADA
I
* Alcove side wall must have a min. of 8”
clearance on one side.
For the State of Massachusetts, installation
and repair must be done by a plumber or
gasfi tter licensed in the Commonwealth of
Massachusetts.
For the State of Massachusetts, fl exible
connectors shall not exceed 36 inches in
length.
For the State of Massachusetts, the appli-
ances individual manual shut-off must be a
t-handle type valve.
The State of Massachusetts requires the
installation of a carbon monoxide alarm in
accordance with NFPA 720 and a CO alarm
with battery back up in the same room where
the gas appliance is installed.
