manualshive.com logo in svg

FP FPi2000, Operator'S Manual, Page: 22 / 26

Share
Download
FP FPi2000 Operator'S Manual Download Page 22

22

Flap sticks.

Store envelopes 
according to 
specifications.

Specifications.

Flap curled.

Envelopes stored or 
manufactured 
improperly.

Specifications.

Separation set too 
narrow.

Check separation 
settings, adjust if 
needed.

Adjustments for 
envelope feeding.

Fingers are placed on 
top of the envelope.

Fingers adjusted too 
deep into the envelope.

Check fingers position, 
adjust if needed.

Envelope insert fingers.

Envelope stops too 
early.

Check envelope stop 
position, adjust if 
needed.

Envelope insert fingers.

Machine stops while 
inserting (stoppage at 
the inserting point).

Fingers not correctly 
adjusted.

Check fingers position, 
adjust if needed.

Envelope insert fingers.

Inserted document too 
long for used envelope.

Check fold settings.

Fold settings menu.

Envelope throat 
incorrect.

Check envelope 
specifications.

Specifications.

Envelope glued inside.

Eliminate faulty 
envelopes.

Specifications.

Window not glued 
properly.

Eliminate faulty 
envelopes.

-

Flap not sufficiently 
moistened.

Water level low.

Check water level, refill 
if needed.

Moistening the brushes.

Brushes dry.

Check brushes, replace 
if needed by the extra 
soaked set.

Moistening the brushes 
or Maintenance.

Brushes dirty.

Check brushes, clean if 
needed.

Maintenance.

Moistening felt dry.

Check the moistening 
felt, refill water tray if 
needed.

Moistening the brushes.

Moistening felt dirty.

Check the moistening 
felt, clean if needed.

Maintenance.

Moistening brushes 
inactive.

Activate the moistening 
brushes.

Envelope sealing.

Symptom

Possible cause

Remedy

Section

Summary of Contents for FPi2000



























Reviews:

No comments