Foxwell BT780 User Manual Download Page 9 | Manualshive

Page: 9 / 21

background image

9

BT780 Battery Analyzer User’s Guide - English Version_V3.00

5. Press the

MENU

button to go to the Main Menu.

NOTE

Do not connect the tester to a voltage source greater than 30V DC; otherwise you may

damage the tester.

NOTE

If you are testing inside a vehicle, make sure all accessory loads are cut off, the key is not in

the ON position and the doors are closed.

3.2 Battery Test

Battery Test

is mainly used to check the cold cranking capability and the aging status of the

battery. It informs the user to replace battery before the battery is getting aged.
To start a battery test:

1. Scroll with the

UP

or

DOWN

button to highlight

Battery Test

from Main Menu and press

the

ENTER

key.

2. Scroll with the

UP

or

DOWN

button to highlight the Technician from Main Menu and

press the

ENTER

Key.

«
...
7
8
9
10
11
...
»

Summary of Contents for BT780






















Reviews:

No comments

Related manuals for BT780

Brand: Kawai Pages: 70

Brand: Omega Engineering Pages: 22

Charge Analyzer 711

Brand: 3M Pages: 24

Brand: M & I Instruments Pages: 2

Brand: +GF+ Pages: 64

Brand: +GF+ Pages: 12

Brand: +GF+ Pages: 48

Brand: Orange Electronic Pages: 21

FG-3000R Series

Brand: Nidec Pages: 8

micro-TRI-gloss ?

Brand: BYK Pages: 174

ACCURE 2350-GAS

Brand: ROOTECH Pages: 26

Brand: THORLABS Pages: 49

Brand: Saluki Technology Pages: 161

Brand: Endress+Hauser Pages: 24

LaserDIMENSIONMASTER 3336

Brand: Calculated Industries Pages: 2

Brand: Omega Pages: 59

Brand: BERG Pages: 23

PMD Analyzer 5500B

Brand: EXFO Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands