Foxfury Lighting Solutions 200-800 Product Manual Download Page 19

19

refurbished product by someone 
other than FoxFury) prior to your 
purchase, you are not the Original 
Purchaser and the product that you 
purchased is not covered by this 
warranty. This limited warranty is 
VOID if this Product has been altered 
or modified in any way (including but 
not limited to attempted warranty 
repair without authorization from 
Foxfury and/or alteration/removal 
of the serial number). To expedite 
warranty concerns, we encourage 
the end user to register their FoxFury 
Product at 

www.foxfury.com/pages/

warranty-registration.

 
THIS IS THE ONLY WARRANTY, 
EXPRESSED OR IMPLIED, 
INCLUDING ANY WARRANTY OF 
MERCHANTABILITY OR FITNESS 
FOR A PARTICULAR PURPOSE. 
INCIDENTAL, CONSEQUENTIAL 
OR SPECIAL DAMAGES ARE 
EXPRESSLY DISCLAIMED EXCEPT 
WHERE SUCH LIMITATION IS 
PROHIBITED BY LAW. 

You may have other specific legal 
rights which vary by jurisdiction. Go 
to www.foxfury.com/pages/warranty 
for a complete copy of the warranty.  
Retain your receipt for proof of 
purchase.

CONTACT FOXFURY

FoxFury, LLC

Oceanside, CA 92056 USA

Toll-Free

: 844-FOXFURY

Tel

: 760.945.4231

Fax

: 760.433.3650

Email

[email protected]

Web

: FoxFury.com

All FoxFury products are designed in 
Oceanside, CA. All FoxFury products 
are manufactured with the highest 
quality USA and foreign parts. 

Products are assembled in either 
FoxFury’s controlled plant in Asia or 
the USA, under strict quality control.

Summary of Contents for 200-800





















Reviews: