background image

 

 
 

SPECIFIC SAFETY INSTRUCTIONS FOR DUST COLLECTORS 

 

 

1.

 

The filtration housing 

contains a high speed fan blade that can amputate fingers, grab loose clothing and 

neckties, and propel dust at high velocities. 

DO NOT OPERATE WITHOUT ALL PARTS IN PLACE.

  

 
2.

 

Do not 

attempt to clean, remove the dust bags, or service the unit when the power is on. Turn the unit off and 

disconnect the cord from the power source.  

 
3.

 

Static shocks 

are common in dry areas or when the relative humidity of the air is low. The use of a humidifier 

where the dust collector is to be used will help raise the relative humidity, and may reduce static shocks.  

 
4.

 

Sparks

 inside the electrical parts can ignite flammable vapours or dust.  

 
5.

 

Do not

 vacuum, or use the dust collector near flammable or combustible liquids, gases, gasoline or other fuels, 

lighter fluid, cleaners, oil-based paints, natural gas, hydrogen, or explosive dusts like coal dust, magnesium dust, 
grain dust, or gun powder. 

 
6.

 

To avoid health hazards

 from vapours or dusts, do not vacuum toxic materials. 

 
7.

 

Do not 

use or store near hazardous material. 

 

8.

 

Do not 

use outdoors or on wet surfaces. 

 
9.

 

Put the unit

 on a stable, level surface. 

 

10.

 

Position

 the vacuum hose and electric cord away from traffic areas. 

 
11.

 

Do not

 allow the unit to be used as a toy. Close attention is necessary when used by or near children. 

 

12.

 

Do not leave

 the dust collector plugged in. Unplug from the outlet when not in use and before servicing. 

 
13.

 

To avoid injury

 from accidental starting, unplug the power cord before changing or cleaning the filter/dust bag or 

chip bag. 

 
14.

 

Do not 

use without the filter/dust bag and/or chip bag in place. 

 
15.

 

Do not

 unplug by pulling on the cord. To unplug, grasp the plug, not the cord. 

 
16.

 

Turn off the controls 

before unplugging. 

 
17.

 

Do not

 use with a damaged cord, plug, or other parts. If your dust collection system is not working as it should, 

has missing parts, has been dropped, damaged, left outdoors, or dropped into water, return it to an authorised 
Service Centre. 

 
18.

 

Do not 

pull or carry by the cord, use the cord as a handle, close the door on the cord, or pull the cord. Keep the 

cord away from heated surfaces. 

 
19.

 

Do not

 handle the plug of the dust collector with wet hands. 

Summary of Contents for F50-841
















Reviews: