37
EN
SETTING THE UPPER TABLE
Make sure that the disk of the mitre saw is perpendicular with the base of the machine
1. Block the mitre saw’s head in the low position, close the lock-knob
(see A- Fig.1)
in the transport position
2. Loosen the rotating base knob and position the base at 0°. Tighten the knob.
3. Loosen the head bevel knob located on the back of the machine and set the position the head at 0°.
Tighten again the head bevel knob.
4. Position one of the sides of a square (not delivered) on the table and the other side against the disk of the
mitre saw. Make sure that the square is correctly positioned along the disk, but not touching the teethes.
When the square is correctly positioned, its two sides must show a continuous contact with the disk and
the table.
5. If this is not the case, please proceed as follows:
•
Loosen the bolts (A) Fig.10 (positioned on each side of the head bevel knob) to release the two bolts.
•
Open the locking lever (C) releasing lever of the mitre saw head, then pull the knob (D) towards you.
•
Position the square against the table.
•
Adjust the two bolts (B) modifying the inclination, until the two sides of the square are in continuous
contact with disk and table.
•
Tighten the locking lever and the locking nuts (C) of the tilting adjustment (A).
•
Check again that the disk is perpendicular with the table.
•
Make sure that the bevel indicator is aligned with 0°
SETTING THE BEVEL ANGLE AND THE STOP
You can tilt the head of the mitre saw from 0 up to 45°, left and right
1. To set the bevel inclination, loosen the head bevel knob
(C)
Fig. 10
positioned on the back of the mitre
saw.
2. To tilt the head on the left, loosen the knob
(D)
then tilt the head from 0° to 45° until you get the destre
inclination, with the help of the operating handle. Once set, tighten the knob again.
3. Release knob (C) to tilt the mitre saw head rightwards, then pull the knob (B) to unlock the tilting angle; tilt
the mitre saw head from 0 to 45° till reaching the desired tilting angle, finally tighten knob (C).
Note
: the angle indicator must be aligned with the 45° sign on each side of the indicator, when the knob
(C)
is
completely loosen and the head is completely inclined on the left or on the right. If you need to adjust it,
proceed as follows
1. Loosen the knob (C) and tilt the head completely on the left.
2. Loosen the inclination stop bolt (A).
3. Adjust the inclination stop hexagonal screw until the angle indicator is aligned with the inclination sign at
45°.
4. tighten the inclination stop bolt (A).
5. Position the blade to 0° then pull the tilting angle unlocking knob (D) to tilt the blade to the other side. The
angle indicator must be aligned with the 45° tilting angle mark.
6. Reposition the head at 0° and make sure that the knob (D) is tighten again.
WARNING ! To prevent the mitre saw from moving during this intervention:
- disconnect the feeder cable.
- Block the head in the lower position and block the radial sliding movement.
- Carry the machine closet o your body to prevent from injuring your back.
Bend on your knees when lifting the machine.
- Lift the machine from the transport handles or from the base. Do not carry it from the power
cable nor from the operating handle: you risk to damage the insulation or the electrical
connection, with serious risk to cause electric shocks or fire.
- position the machine in not too crowded areas, where people are not supposed to circulate nor
rest. The wood chips ejected could injury people around the machine.
- Fix the machine on a stable surface, so that it can not tilt.
Summary of Contents for F36-257DB
