Four-Faith F2816 V2 User Manual Download | Manualshive

Page: 19 / 56

background image

Page 19 of 56

Chapter 3 Configuration

3.1 Connection

Before configuration, It’s necessary to connect the IP MODEM with the PC by the shipped RS232
or RS232-485 conversion cable as following.

3.2 Configuration Introduction

There are two ways to configure the IP MODEM:

Configuration software tool:

All the settings are configured through the shipped software tool.
It’s necessary to have one PC to run this tool

.

Extended AT command:

All the settings are configured through AT command, so any device with serial port can configure
it.
Before configuration with extended AT command, you should make IP MODEM enter configure
state.
The steps how to make IP MODEM enter configure state, please refer to appendix.

The following describes how to configure IP MODEM with the configure software tool. At the

«
...
17
18
19
20
21
...
»

Summary of Contents for F2816 V2

























































Reviews:

No comments

Related manuals for F2816 V2

Brand: ICP DAS USA Pages: 4

Brand: ICP DAS USA Pages: 4

Brand: ICP DAS USA Pages: 21

Brand: ICP DAS USA Pages: 6

Brand: T-Mobile Pages: 10

Brand: BROSTREND Pages: 13

MobilityPass 3G

Brand: Nokia Pages: 6

Internet Stick CS-19

Brand: Nokia Pages: 17

Brand: Nokia Pages: 17

Brand: Nokia Pages: 18

Brand: Nokia Pages: 17

Internet Stick CS-18

Brand: Nokia Pages: 25

Brand: upcom Pages: 13

Brand: Go Pages: 2

Brand: Davicom Pages: 27

Brand: Davicom Pages: 29

Brand: 3Jtech Pages: 4

Brand: 3Jtech Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands