background image

The factory preset position is the center,0dB position.

There are 3 positions:-3dB,0dB,+3dB.

The High Frequency adjustment tailors the overall high frequency response by +/-3dB

positions a full +/-3dB can be achieved. Leave this adjustment in the normal "0dB"

above 5kHz. This control is a variable knob with no preset position. In the extreme

position unless:

Back Panel Overview

This input is an electronically balanced input and

1. XLR & TRS Combination Input

signals.

This control adjusts the input level to the internal

amplifiers.

The heatsink dissipates heat from the amplifier.  It

is compatible with both -10dBV and +4dBu

2. Continuously variable gain control

3. Heatsink

4. Power Switch

5. Standard IEC Power Input

7. High Frequency Adjustment

6. Low Frequency Adjustment

is important the heatsink receives proper

ventilation and is not placed near any sources of

heat.

Turns power to the amplifier section on or off.

On-position is the spot side.

This powor terminal should be used with a

properly grounded three pin power cable, such as

the one provide with the product.

response to get suit its environment.

The PM-2 allows you to adjust its low frequency

There may be cases where a slight adjustment

acoustic characteristics of the room.

is necessary in order to better match the

To make this adjustment you may boost or

simply by turning the switch to the right or the

cut the PM-2's low frequency @ 60Hz by 3dB

left respectively.

• You want to compensate for any HF hearing loss

• You want to subtly brighten or darken the sound of the speakers

• You just like to mix on the bright or dull side

indicates that you monitors are too bright relative to your normal hearing. A bit less high

If your mixes consistently sound dull or dark when you listen elsewhere, this usually

frequency energy usually fixes this, and you can force the mix in this direction by

reducing the high frequency output of the monitors by turning the knob in the -3dB

direction. The converse is true if your mixes are consistently sounding bright and present.

p-6

Summary of Contents for PM-2









Reviews: