background image

 

 

 

 

 

LIMITATIONS OF IP PROTECTION 

 

IP-Rating doesn´t mean unlimited outdoor use and protection against any kind of environmental 

influence! Especially sunlight and included UV will bring accelerated aging. Some fixtures need special 

parts or processes to fit the rated IP-Protection, like mounting covers or caps or similar. Sealings and other 

plastic or rubber materials are aging parts. They must be checked frequently to ensure the protection and 

safety of the fixtures. Also specified torque of screws can affect protection! 

 

Installation 

 

Hanging:

 The fixture can be mounted in a hanging position using the supporting bracket.  The bracket 

should be secured to the mounting truss or structure using a standard mounting clamp.  Please note that 

when hanging the unit, a safety cable should also be used. 

UPRIGHT:

 The fixture can be mounted in an upright or sitting position using the supporting brackets. 

 

NOTE!

 If the signal cable is over 60 m between the DMX512 controller and fixture or between 

two fixtures, then a DMX signal amplifier is needed as well. 

 

 
Menu Screen 

 

You can easily navigate through menu’s options with the four buttons under the screen. Navigating in the 

menu is simple! With the Up / Down buttons, you are moving through menu’s choices, pressing Enter, 

you are entering the sub menu of the option you have chosen, with the Up / Down buttons you’re moving 

through the sub menu’s options, with Enter, you are confirming your choice. The 

FOS Cyclone RGB

 offers 

the following options: 

 

Addr:

 Set the DMX address. 

Chnd:

 Select the channel mode. Press Enter and the Down / Up buttons for choosing between the 5 modes 

(1, 2, 4, 6 & 7)

Summary of Contents for Cyclone RGB









Reviews: