Forza BOLT XW4A-4 Owner'S Manual Download Page 6

5. Preparation

1. Lubrication Information
Use high quality clean lubricants, we do not recommended any special additive 
lubricants. Please  Add 320ml of oil for new machines, then check the oil level gauge 
scale to ensure the correct amount of oil. 
Figure (1)

2. Fuel Information
Only use clean, unleaded gasoline. (87 Octane or above). Gasoline should be used within 
30 days of purchase. DO NOT use gasoline containing more than 10% Ethanol.
NOTICE: Turn off the outboard motor and let the engine cool at least 2 mins before 
refueling.

6. Operation

1.Preparation before starting

1.1 Push the priming bulb on carburetor until fuel flows through the return fuel line.
1.2 Move choke lever to the closed position(Figure 4-direction of the arrow reversed in 
the end). Once the engine warms up, move the choke lever to the fully open position.

2.Starting

2.1 Recoil start

Pull the starter grip lightly until resistance is felt,then pull briskly starting the engine. 
D ifficulty in starting may occur due to too much fuel, remove the spark plug. Fully open
choke lever and pull recoil starter 5-6 times, then reinstall the spark plug, and restart 
using the method above.

Summary of Contents for BOLT XW4A-4

















Reviews: