Forza BOLT XW4A-4 Owner'S Manual Download Page 16

When cruising normally, outboard motor should be same as figure 11 
When operating in Reverse boat, Outboard motor status same as figure 12
When   operating   in   reverse,   use   a  slow  speed,   otherwise  the  boat  will  be  unstable.
Outboard  motor  bracket  can  rotate 

360  °.Simply  rotate  180  °,   move  steering  handle

toward the rear, and the  boat can go backwards.

Notice:

1. After cruising the sea or turbid water, please wash the outboard motor body using
fresh  water. Do not spray water into the air intake.

2. Store the outboard motor in a dry, well ventilated place,not in direct sunlight. 
3. For long-term storage, the fuel tank should be emptied
4. Do not paint the anode block, otherwise it will cause anode block failure. Regularly 
check  the anode block and remove any dirt.

12.Model Specifications

Model: XW4A-4 Type1 
Cylinder, Air-Cooling, 4 stroke,OHV
Bore*stroke(mm): 70*45
Displacement(cm³): 53.2
Max output (kw/r/min): 2.2/5000
Full throttle operating range: 3800-5200RPM
Fuel consumption: 480g/kw.h
Fuel: 87+ Octane Unleaded gasoline
Fuel tank capacity:1.2L
Engine oil capacity: 0.32L
Gear oil Capacity: 43ML
Gear Ratio: 27:13
Lubricating system: Splash lubrication
Cooling method: Forced cooling
Ignition system: TCIStart system
Recoil start: Start with strong way Choke valve
Propeller options: 3x7 1/4"x5"
Transom height: 417mm(16.4 in)
Gross weight: 12KG
Size(mm): 95*41*27.5cm

Summary of Contents for BOLT XW4A-4

















Reviews: