Fortress Technologies ALARM COMBO SYSTEM FS-50 Installation Handbook Download Page 32

Page: 32 / 32

DATA PORT DIAGRAM

This unit includes DP Technology that will allow you to directly Plug-In our Data Port Bypass Modules.

There are 2 types of

Protocol, OFA series and SL series modules. The default is set for SL series Protocol. Please refer to Databus
module manual for detail instructions. The Data Port Protocol must be programmed for the correct module.

See Option # 7 on page 20

Vehicle

ign with

Anti-theft

iDATA LINK CABLE

Data Port

Module Not Included

Antenna

NOTE: Most Vehicles 1998 and up

have a Anti- theft system on it.

Please check Tech Notes on vehicle

before installtion.

Bypass

Module

www.crimestopper.com

Phone (800) 998-6880

FAX (805) 581-9500

ONLINE TECHNICAL SUPPORT

www.crimestopper.com

Summary of Contents for ALARM COMBO SYSTEM FS-50

































Search results

Summary of Contents for ALARM COMBO SYSTEM FS-50

Reviews:

Related manuals for ALARM COMBO SYSTEM FS-50

Brands by name

Popular brands

Fortress Technologies ALARM COMBO SYSTEM FS-50, Installation Handbook

Search results

Summary of Contents for ALARM COMBO SYSTEM FS-50

Reviews:

Related manuals for ALARM COMBO SYSTEM FS-50

Brands by name

Popular brands