Fortinet FortiGate 5001FA2-LENC Manual Download | Manualshive

Page: 12 / 34

background image

FortiGate-5001FA2-LENC Security System Guide

12

01-30000-76602-20080606

Changing FortiGate-5001FA2-LENC jumper settings

Hardware installation

Normally, because the jumpers are factory set, you do not have to change them.
However, if you are moving a FortiGate-5001FA2-LENC from a FortiGate-5140 or
FortiGate-5050 to a FortiGate-5020 or the reverse, you need to move the JP3
jumper.

Also, if a new FortiGate-5001FA2-LENC board does not function properly, you
should check the JP3 jumper settings.

Figure 3: FortiGate-5001FA2-LENC jumper settings

Table 3: FortiGate-5001FA2-LENC JP3 jumper settings for each chassis

Chassis

Correct JP3
Jumper Setting

Result of wrong jumper setting

FortiGate-5140 pins 2 and 3

Shelf manager cannot find FortiGate-5001FA2-LENC

board. No chassis information available.

FortiGate-5050 pins 2 and 3

Shelf manager cannot find FortiGate-5001FA2-LENC

board. No chassis information available.

FortiGate-5020 pins 1 and 2

FortiGate-5001FA2-LENC board will not start up.

Note:

If the shelf manager in a FortiGate-5140 or FortiGate-5050 chassis is missing or not

functioning, FortiGate-5001FA2-LENC boards with JP3 jumper connecting pins 2 and 3 will
not start up. To operate FortiGate-5001FA2-LENC boards in a FortiGate-5140 or FortiGate-
5050 chassis without a shelf manager, set the JP3 jumper to connect pins 1 and 2.

JP3

JP2

JP1

Front Faceplate

5050 and 5140 chassis

5020 chassis

Pins 2 and 3

Pins 1 and 2

JP3

JP3

«
...
10
11
12
13
14
...
»

Summary of Contents for FortiGate 5001FA2-LENC



































Reviews:

No comments

Related manuals for FortiGate 5001FA2-LENC

RG-WALL1600-S3600

Brand: Ruijie Networks Pages: 28

Proventia Network GX4004

Brand: IBM Pages: 3

ZyXEL ZyWALL IDP 10

Brand: ZyXEL Communications Pages: 111

Brand: Ronde & Schwarz Pages: 129

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands