4/6
User manual built-in burners
3. User manual: built-in burner
4. Technical data: FORNO
®
built-in burners
- Always make sure the instructions in this user manual are followed exactly. If these instructions are not followed in the correct way, it may
result in a fire or explosion that could cause damage to people, property or loss of life.
- Never use flammable liquids or vapors in the vicinity of a burning device.
- Improper installation, adjustments or modifications to the equipment can result in injury or property damage. Read the installation instructions,
safety precautions and operating instructions very carefully.
- Do not leave the FORNO
®
built-in burner unattended when in use or when connected to an opened gas bottle.
What to do if the device emits a smell of gas:
- Directly close the bottle and contact a technical gas specialist. Do not use the device until it is approved for use again.
- Installation, maintenance and service needs to be done by a qualified gas professional in this cases.
- Only use the FORNO
®
built-in burner outdoor or in a well-ventilated area. Never use the built-in burner inside a building, house, garage or
any other enclosed area.
- Gas bottles must be placed outdoors and stored in well-ventilated areas. Make sure that gas bottles are out of reach for children. Gas bottles
which are not used or disconnected from the FORNO
®
built-in burner should not be stored in a building, garage or any other enclosed area.
- The FORNO
®
built-in burner is best stored in a garage or well-ventilated area. Store the FORNO
®
built-in burner only when it is disconnected
from the gas bottle.
- The FORNO
®
built-in burner is not approved as a cooking appliance and must not be used as such.
- Check at least every month and every time a change is made to the unit if the FORNO
®
built-in burner has no gas leaks.
- Keep the area around the FORNO
®
built-in burner clear of combustible liquids, materials and vapors.
- Never throw anything in the gas fire of the FORNO
®
built-in burner.
- Never use a fuel other than propane gas.
Turning on the FORNO
®
built-in burner
- Make sure the FORNO
®
built-in burner is installed properly and is stable.
- Remove the lid
- Press the red ignitor until you hear a soft ticking sound (this is the piezo ignition). If you hear nothing when pressing the ignition button, then
you probably need to replace the battery. Hold the control knob pushed in when you open the gas supply. Turn the control knob to the right
for gas supply. The burner should now ignite within 15 seconds . Keep the control knob pushed in for an additional 15 seconds after the flame
has fully ignited. Release the knob and the flame should continue to burn. If not, repeat the process but hold in the control knob longer after
igniting the flame.
Switching off the FORNO
®
built-in burner
- Turn the control knob to the left so the flame goes out. If the flame is out, turn off the gas valve on the gas bottle.
- Let the lava rocks and ceramic logs cool down completely and place the stainless steel cover on the built-in burner.
Which gas bottle can be used for FORNO
®
built-in burners
The FORNO
®
built-in burners have been extensively tested for propane gas. Therefore, always use one of the required gas cylinders. Using an
-
other bottle can give another fire behavior, or in the worst cases cause major damage to people, animals or materials. If you are unsure about a
particular cylinder. Please always contact the helpdesk of FORNO
®
or an authorized gas specialist.
Do you have any questions about our products please contact us via our website: www.forno.nl
Liessentstraat 4
5405 AG Uden
Tel. +31 (0)413 274 168
Warranty FORNO
®
built-in burners:
FORNO
®
gives a two-year warranty on the gas technical system FORNO
®
built-in burners.
FORNO
®
Recessed square Burner
Gas type
Propane G31
Heating Capacity
8,5 kW
Atomizer opening
2.05-2.3 mm
Dimensions in mm
405x405mm outer size
360x360mm installation size
FORNO
®
Recessed rectangle Burner
Gas type
Propane G31
Heating Capacity
11,8 kW
Atomizer opening
2.05-2.3 mm
Dimensions in mm
800x190mm outer size
760x150mm installation size
