Ford Windstar Owner'S Manual Download Page 296 | Manualshive

Page: 296 / 385

background image

296

*

[MC11200(ALL)05/96]

Leave the coolant in all year. Make sure that the coolant will
not freeze at the temperature level in which you usually drive
during winter months. Keep an engine coolant in your engine
that has a protection rating of at least

s

20˚F (

s

29˚C).

*

[MC11300(ALL)05/96]

To find out how much engine coolant mixture your vehicle’s
coolant system can hold, see Refill Capacities in Capacities and
Specifications chapter.

[MC11400(ALL)01/96]

You may add water by itself only in an emergency, but you
should replace it with a 50/50 mixture of water and coolant as
soon as possible.

*

[MC11500(ALL)05/96]

Have your dealer check the engine cooling system for leaks if
you have to add engine coolant more than once a month, or
you have to add more than a quart (liter) at a time.

%

*

[MC11600(ALL)01/96

]

Checking Hoses

*

[MC11700(ALL)01/96]

Inspect all engine and heater system hoses for deterioration,
leaks and loose clamps before adding or replacing engine
coolant. Make whatever repairs or replacements are necessary
using Motorcraft parts or their equivalents.

%

*

[MC11800(ALL)05/96

]

Engine Coolant Drain and Flush

[MC11900(ALL)01/96]

To drain and flush your engine coolant, you MUST see your
Ford dealer or refer to the procedure in the service manual.
Failing to do so could result in engine damage.

% [MC12000(ALL)04/96]

Power Steering Fluid

*

[MC12100(ALL)01/96]

Check the level of the power steering fluid at least twice a
year (i.e., every Spring and Fall).

*

[MC12200(ALL)01/96]

To check the level of your power steering fluid:

[MC12300(ALL)01/96]

1.

Start the engine and let it run until the power steering fluid
reaches normal operating temperature. The power steering
fluid will reach the right temperature after at least five
minutes of idling or at least one mile (1 km) of driving.

File:11wnmcs.ex

Update:Mon Jul 8 14:29:32 1996

«
...
294
295
296
297
298
...
»

Summary of Contents for Windstar


































































































































































































































































































































































































Reviews:

No comments

Related manuals for Windstar

AUDI 4G HIGHEND

Brand: KAP Pages: 20

PRIME DESIGN VCR 326

Brand: Safe Fleet Pages: 16

Prime Design VBC PC11

Brand: Safe Fleet Pages: 8

Prime Design AR1418

Brand: Safe Fleet Pages: 4

Cushman Turf Truckster

Brand: Jacobsen Pages: 210

ANDROID INTERFACE

Brand: GMC Pages: 18

Brand: Prorack Pages: 15

Brand: EUFAB Pages: 12

WrapAround Windjammer

Brand: Bestop Pages: 7

Brand: Axxess Pages: 8

Brand: Chevrolet Pages: 376

Brand: Mazda Pages: 15

Brand: Rago FABRICATION Pages: 10

Brand: Saab Pages: 288

Brand: Sunsky Pages: 9

Brand: Ecco Pages: 9

Brand: Skoda Pages: 165

Brand: Cadillac Pages: 409

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands