manualshive.com logo in svg

Ford BRONCO 1967, Installation Manual

Share
Download
Ford BRONCO 1967 Installation Manual Download Page 21

www.classicautoair.com • 866.435.7801

PAGE

21 

The engine compartment components should be installed at this time. Carefully 

follow the electrical diagram provided on page 8.

COMPRESSOR MOUNTING COMPONENTS WILL DIFFER DEPENDING ON 

ENGINE AND DRIVE ACCESSORIES THAT YOUR VEHICLE IS EQUIPPED WITH. 

THE FOLLOWING INSTRUCTIONS SHOW THE PROPER INSTALLATION 

SEQUENCE FOR THIS VEHICLE 

Locate the following components from the under hood components box:

Condenser

Discharge Tube

Liquid Tube 

(4) Condenser mounting brackets

(8) #10 x 3/8 hex washer head screws

 Remove Radiator Fan, Shroud and the Radiator. Retain the original mounting 

hardware.

Locate the drivers side radiator support Template from last few pages of the instal-

lation instructions.

Locate template on the radiator support and drill (1) hole 7/8” diameter.

Locate the passengers side radiator support Template from last few pages of the 

installation instructions.

Locate template on the radiator support and drill (1) hole 3/4” diameter.

Summary of Contents for BRONCO 1967






































Reviews:

No comments

Brands by name

Popular brands

Load more brands