Ford 2009 Town Car Owner'S Manual Download Page 15

Page: 15 / 280

O/D off:

Illuminates when the

overdrive function of the
transmission has been turned off;
refer to the

Driving

chapter. If the

light does not illuminate, have the transmission serviced soon, or damage
may occur.

Speed control:

Illuminates when

the speed control is activated. Turns
off when the speed control system
is deactivated.

Turn signal:

Illuminates when the

left or right turn signal or the
hazard lights are turned on. If the
indicators stay on or flash faster, check for a burned out bulb.

High beams:

Illuminates when the

high beam headlamps are turned on.

Headlamps on warning chime:

Sounds when the headlamps or parking

lamps are on, the ignition is off (the key is not in the ignition) and the
driver’s door is opened.

Key-in-ignition warning chime:

Sounds when the key is left in the

ignition in the off or accessory position and the driver’s door is opened.

Turn signal chime (if equipped):

Sounds when the turn signal lever

has been activated to signal a turn and not turned off after the vehicle is
driven more than 1/2 mile (0.8 km).

O/D

OFF

2009 Town Car

(tow)

Owners Guide, 1st Printing
USA

(fus)

Instrument Cluster

Summary of Contents for 2009 Town Car

























































































































































































































































































Search results

Summary of Contents for 2009 Town Car

Reviews:

Related manuals for 2009 Town Car

Brands by name

Popular brands

Ford 2009 Town Car, Owner'S Manual

Search results

Summary of Contents for 2009 Town Car

Reviews:

Related manuals for 2009 Town Car

Brands by name

Popular brands