414-03A-72
414-03A-72
High Voltage/Traction Battery
DIAGNOSIS AND TESTING (Continued)
PINPOINT TEST A: DTC C1755 POWER LIMIT SHUTDOWN FAULT
TEST STEP
ACTION TO TAKE
Yes =
Go to A5
•
WARNING: Make sure the cooling system temperature is not
hot. Failure to follow these instructions, may result in personal
injury or death.
Turn the ignition key ON, remove the radiator cap, and check for coolant
flow.
•
Is there coolant flow?
No =
Check the cooling system
for restrictions. Refer to
Pump does not operate.
A5 MONITOR THE TIM AND TRANSAXLE TEMPERATURE
•
Monitor PID TIMTEMP during a road test.
Yes =
Check for cooling system
restrictions at TIM.
•
Is the temperature above 80
°
C (176
°
F)?
No =
Intermittant problem in the
water pump circuit or the
water pump.
PINPOINT TEST B: BATTERY PACK/MODULE(S) VOLTAGE OUT OF RANGE
TEST STEP
ACTION TO TAKE
B1 CHECK FOR OTHER BATTERY CONTROL MODULE (BCM)
DIAGNOSTIC TROUBLE CODES (DTCs)
•
Perform the on-demand self-test for the BCM.
Yes =
•
Does DTC C1864 Battery Module Fault occur?
No =
GO to B2.
If DTC B1676 Battery Pack
Voltage Out of Range
B2 CHECK BATTERY MODULE FAULT STATUS
•
With key ON, monitor BCM PIDs BTM 1FT thru BTM39FT.
Yes =
GO to B3.
•
Do any of the battery module fault PIDs indicate YES?
No =
B3 CHECK VOLTAGE SENSE LINE CIRCUIT BETWEEN BCM AND
IN-LINE CONNECTOR FOR OPEN
•
Remove the traction battery and connect Traction Battery High-Voltage
Yes =
Lockout and Diagnostic Tool to the traction battery high-voltage two-pin
C3994M.
No =
WARNING: The traction battery contains high-voltage
components and wiring. High-voltage insulated safety gloves and face
shield must be worn when performing the following steps. Failure to
follow this warning may result in severe personal injury or death.
•
With key OFF, disconnect BCM high-voltage C1865, C1866 and the
appropriate in-line connector for the battery module(s) in question.
NOTE: If a single battery module fault PID (with the exception of
BTM 1FT and BTM39FT) indicates YES, check the battery module in
question for reverse cable polarity. Reinstall (correctly) if necessary. If the
cable polarity is OK, GO to B6.
•
Measure the resistance of the wire between the BCM high-voltage
connector and in-line connector for the indicated battery module fault(s).
Use the following information:
Battery Module Faults
(Continued)
2001 Ranger EV, 01/2001
Summary of Contents for 2001 Ranger
