manualshive.com logo in svg

Ford 1998 F-150, Workshop Manual, Page: 7 / 74

Share
Download
Ford 1998 F-150 Workshop Manual Download Page 7

No

 

REPLACE the fuse(s). CLEAR the DTCs. TEST the system for normal operation. If the fuse(s) 
fail again, CHECK for a short to ground. REPAIR as necessary. 

 

A3

 CHECK CIRCUIT 1052 (T/BK) FOR VOLTAGE

 

 

Fuse Junction Panel C243 

 

 

Measure the voltage between fuse junction panel C243-11, circuit 1052 (T/BK), and ground. 

 

Is the voltage greater than 10 volts?

 

Yes

 

REPLACE the fuse junction panel. CLEAR the DTCs. TEST the system for normal operation. 

 

No

 

REPAIR circuit 1052 (T/BK). CLEAR the DTCs. TEST the system for normal operation. 

 

A4

 CHECK THE IGNITION STATES — MONITOR THE GEM PID IGN_GEM

 

 

 

 

NGS 

 

 

NOTE: 

If the vehicle is equipped with a manual transmission, depress the clutch pedal while 

turning the ignition switch to the START position. 

Monitor the GEM PID IGN_GEM and rotate the ignition switch (11572) through the START, 
RUN, OFF, and ACC positions. 

 

Do the PID values agree with the ignition switch positions?

 

Yes

 

GO to 

A5

. 

 

No

 

REPAIR the ignition circuit(s) (RUN/ACC: circuit 297 [BK/LG], RUN: circuit 1040 [R/LB], 
START: circuit 32 [R/LB] or circuit 481 [GY/Y]) in question. CLEAR the DTCs. TEST the 
system for normal operation. 

 

A5

 RETRIEVE THE DIAGNOSTIC TROUBLE CODES (DTCS)

 

 

Retrieve and Document Continuous DTCs 

 

 

Clear Continuous DTCs 

 

 

GEM On-Demand Self-Test 

 

Are any DTCs recorded?

 

Page 7 of 74

1998 F-150/250 Workshop Manual

1/11/2011

http://www.fordtechservice.dealerconnection.com/pubs/con...

Summary of Contents for 1998 F-150











































































Reviews:

No comments