background image

This exercise equipment is built for optimum safety. However, certain precautions apply whenever you

operate a piece of exercise equipment. Be sure to read the entire manual before you assemble, operate

or use this equipment.

Assembly

• The product must be installed on a stable and level

surface.

• Assemble the item as close to its final position

(in the same room) as possible.

• Make sure you have enough space to layout the

parts before starting.

• Keep children and animals away from the exercise

area, small parts could pose a choking hazard if

swallowed.

• Dispose of all packaging carefully and responsibly.

• Check you have all the components and tools

listed in the parts list, bearing in mind that, for

ease of assembly, some components are pre-

assembled.

• The assembly of this equipment is best carried out

by 2 people.

Use

• It is the responsibility of the owner to ensure that all

users of this product are properly informed as to how

to use this product safely.

• This product is intended for domestic use only.

Do not

use in any commercial, rental, or institutional

setting.

Use the equipment only for intended use, as

described in this manual. Do not use attachments not

recommended by the manufacturer.

• Keep this equipment indoors, away from moisture

and dust. Do not put the equipment in a garage,

outbuilding, covered patio, or near water.

• Your product is intended for use in clean dry

conditions. You should avoid storage in excessively

cold or damp places as this may lead to corrosion

and other related problems that are outside our

control.

• Keep unsupervised children away from the

equipment.

• Parents and others in charge of children should be

aware of their responsibility because the natural play

instinct and the fondness of experimenting of

children can lead to situations and behavior for which

the training equipment is not intended.

• If children are allowed to use the equipment under

supervision, their mental and physical development

should be taken into account. They should be

controlled and instructed to the correct use of the

equipment. The equipment is under no

circumstances suitable as a toy.

• Disabled persons should not use the equipment

without a qualified person or doctor in attendance.

This product is not suitable for therapeutic

purposes.

• Always wear appropriate workout clothing when

exercising.

Do not

wear loose or baggy clothing, as

it may get caught in the equipment. Wear trainers

to protect your feet while exercising.

Do not

place any sharp objects around the

equipment.

• Keep hands away from all moving parts.

• If any of the adjustment devices are left projecting,

they could interfere with the user’s movement.

• Before using the equipment to exercise, always

perform stretching exercises to properly warm up.

• Only one person at a time should use the

equipment.

• A spotter is recommended during exercise.

• If the user experiences dizziness, nausea, chest

pain, or other abnormal symptoms

stop the workout

and seek immediate medical attention.

• Injuries to health may result from incorrect or

excessive training.

• This product is suitable for a maximum user weight

of:

 

120kg.

Warning: Before beginning any exercise program, consult your doctor. This is especially important 

for people over the age of 35 or persons with pre-existing health problems or those who have not 

exercised for a period of time. You MUST read all instructions before using any fitness equipment. 

FORCE USA and its associates assume no responsibility for personal injury or property damage 

sustained by or through the use of this product.

Important –

Please read fully before assembly or use

Safety information

1

Summary of Contents for JX-DS913



































Reviews: