background image

DESCRIPTION 

Wireless personal monitor system for audio signal transmission in the band UHF 863-865 MHz. The system is
composed of a wireless in ear belt-pack monitor receiver (mod. 

RI-840

) with silicone rubber earphones and

a wireless hand-held microphone transmitter (mod. 

MSHT-40M

) or a tie-clip microphone (mod. 

MSHT-45P

)

with wireless belt-pack transmitter, depending on the model chosen.

The system has 40 transmission channels in the band UHF 863-865 MHz, with PLL frequency control which
allows a transmission channel free of interference to be easily selected.
It is possible to use multiple receivers (

RI-840

) in the same channel with one transmitter.

CONTROLS AND FUNCTIONS

RI-840

Wireless in ear belt-pack monitor receiver with headphones.

1.-

Information display

: displays information on tuned frequency, channel number, battery level, RF signal

level and audio signal level. If the level of the batteries is low, the display will light up red.

2.-

w

/

s

: allow menu options to be selected in order to configure the wireless belt-pack receiver.

3.-

SET

: allows selection among the different configuration options: channel number and frequency, RF

transmission level (high/low), battery type selection (1.2 V - rechargeable/1.5 V - alkaline) to display the
battery level correctly and lock the receiver. In order to do so, press the SET button repeatedly and use
the 

w

/

s

buttons to select the options.

4.-

Battery compartment

: uses two 1.5 V LR6-AA batteries, alkaline or rechargeable.When inserting the

batteries, make sure the polarity is correct.

5.-

HEADPHONES OUTPUT

: select the type of headphone output signal, single (L+R channels in left earphone)

or double (L+R channels in both earphones).

6.-

Contacts to recharge the rechargeable batteries of the wireless receiver in the recharge docking station mod.

MSC-2

.

7.-

Antenna.

8.-

VOL

: wireless belt-pack receiver volume control.

9.-

3.5 mm stereo jack connector for connecting headphones/recording. If you wish to record a signal
received by the receiver 

RI-840

, connect the recording equipment to the headphone output or use an

adapter to be able to use the headphone signal and the recorder simultaneously.

10.-

POWER

: receiver on/off switch.

Note

:  when the SET button is pressed to configure the different parameters of the receiver, a MUTE indicator

appears  in  the  display  and  the  receiver  will  not  receive  audio  while  the  parameters  are  being
configured.

- 4 -

EN

TMRI-844_TPRI-845, TSRI-841_MANUAL_(EN)_20180315_Maquetación 1  15/3/18  12:30  Página 4

Summary of Contents for TMRI-844

















Reviews: