background image

- 3 -

SIGNIFICANCE OF THE SYMBOLS ON THE MACHINE*

The  symbol  formed  by  the  expression  “Class  1  laser  product”  written  in  a  rectangle
indicates that visible or invisible laser radiation could be produced. Avoid direct exposure
to the laser.

The symbol formed by a ray of lightening inside a triangle shows that the machine has
connection terminals or a circuit with areas with a current which could cause an electric
shock, even in normal working conditions.

The symbol formed by an exclamation mark in a triangle shows that the instruction manual
must be referred to for information on how the machine works and its use.

The  symbol  formed  by  one  square  inside  another  square  shows  that  the  machine  has
double electrical insulation.

The  European  Community  symbol  shows  that  the  machine  complies  with  the  current
European Union legislation, as well as its transposition to local legislation.

The symbol of a rubbish bin crossed out and over a horizontal line shows that when the
product is disposed of it must be done properly, placing it in a special selective electronic
and electrical equipment container or through a dealer when purchasing a similar product,
at no additional cost. It also shows that the machine was put on the market after 13th
August  2005  (European  Community  Directive  2002/96/CE  of  Electrical  and  Electronic
recycling, and its Spanish equivalent R.D.208/2005).

In accordance with what is set out in the aforementioned decree, FONESTAR is registered
in  the  RAEE  (Registro  de  Aparatos  Eléctricos  y  Electrónicos)  in  a  special  section  REI
(Registro de establecimientos Industriales), with the entry number 001851.

The symbol RoHS (Restriction of Hazardous Substances) shows that the product has been
designed and manufactured restricting the use of certain dangerous materials (Directive
2002/95/CE on the restriction of certain dangerous substances in electrical and electronic
appliances, and its transferal to the Spanish regulations, R.D.208/2005).

*It is possible that some of these symbols do not appear on the machine.

EXEMPTION OF LIABILITY

The characteristics of the equipment and the content of the manual can change without forewarning.

FONESTAR, S.A

. does not assume responsibilities regarding the inappropriate use of the equipment or the

information supplied in this instruction manual, and specifically disclaims any implied liability for marketability
or fitness for any other use.

All rights reserved by 

FONESTAR, S.A.

EN

Summary of Contents for MAX-62









Reviews: