background image

 

1.2 Operating the boiler 
 
1.2.1 Switching on 
* open the gas tap; 
* set the power mains switch to 
ON; 
* set the desired boiler 
operating mode through switch 

Summer/OFF/Winter/Anti-

freeze; power light B comes on. 
Sselecting the Summer mode 
the boiler supplies DHW only; 
selecting the Winter mode the 
boiler supplies both central 
heating and DHW; with the 
Anti-freeze mode central 
heating and DHW functions are 
not active and the boilers is 
protected against freezing; 
* set the temperature value 
desired for the central heating 
through the CH regulator C;  
* set DHW temperature through 
knob 

D; if the water 

temperature in the storage tank 
is lower than the one set on the 
boiler, the boiler automatically 
heats it to the set value.  The 
boiler prioritizes DHW and 
water tank temperature 
holding functions to central 
heating function. 
 Control 
knob allows setting of 
temperature in a 40 °C to 60 °C 
range: when the knob is in 
middle position DHW is set to 
approximately 50 °C; 
* set room temperature through 
the ambient thermostat if 
available; 
 
Warning: when starting the 
boiler after a long period of 
inactivity, particularly boilers 
powered by LPG, air bubbles 
may be present in the supply 
line. 
Before switching on the boiler 
switch on another gas powered 
device (e.g. Light a  kitchen gas 
appliance). 
The boiler may still shut down 
once or twice. 
If boiler shuts down use the 
reset button F  to resume 
operation (see below). 
 
 

 
1.2.2 Boiler shutdown 
In case of malfunction the boiler 
automatically turns off: the 
shutdown light E on the control 
panel comes on. Then follow 
the below instructions: 
* check that the gas tap is open 
and that gas is flowing, for 
example by lighting a kitchen 
gas appliance; 
* if there is gas supply wait for a 
minute before restarting the 
boiler using reset button F if the 
boiler does not restart, try to 
reset the boiler three additional 
times. Should the boiler still not 
resume operation, call an 
authorised Service Centre or 
qualified maintenance 
personnel. 
 
If the boiler shuts down 

 

frequently,  this indicates that 
there is a recurring 
malfunction
. In this case 
contact qualified personnel or 
an authorised Service Centre 
for maintenance. 
 
WARNING 
In order to prevent flue gas 
leaks, natural draught boilers 
are fitted with a safety device 
with automatic reset. When 
the safety device detects a 
leak, the boiler holds standby 
mode for 15 minutes. 
 
Should the above mentioned 
boiler status frequently 
occur, the flue system  is not 
properly functioning. In this 
case contact a qualified 
technician to check the flue 
system. A persistent 
malfunction in the flue 
system might put people and 
animals at risk. 
 
1.3 Maintenance 
 
The boiler must be serviced 
once a year. 
Correct servicing ensures boiler 
performance, prevents 
environment pollution and 

potential danger for people, 
animals and property. 
The boiler must be serviced by 
qualified personnel. FONDITAL 
strongly recommends 
customers to refer exclusively 
to qualified personnel. 
 
The user may only clean the 
exterior boiler housing using 
domestic products . 
Do not use water! 
 
1.4 Information for the user 
 
The user can access only the 
parts of the boiler which can 
be reached without using 
tools: it is therefore forbidden 
to disassemble the exterior 
cover of the boiler and 
tamper with the interior parts. 
NO-ONE, INCLUDING 
QUALIFIED PERSONNEL, 
MAY MAKE MODIFICATIONS 
TO THE BOILER.  
 
FONDITAL cannot be held 
liable in the event of injury to 
persons and animals and 
damage to property resulting 
from tampering or improper 
operations on the boiler. 
 
If the boiler is inactive and 
disconnected from the power 
supply for long periods the 
pump might be blocked and it 
may be necessary to manually 
turn  the pump rotor to resume 
its operation. 
 
The above mentioned 

 

operation, which requires 
disassembling the boiler 
housing and accessing internal 
parts of the boiler, must be 
performed by qualified service 
personnel. 
 
It is possible to prevent the 
pump from blocking by adding 
special filming products suitable 
for multi-metal systems to the 
water. 
 
If the boiler is not disconnected 
from the mains power supply, 

Summary of Contents for NIAS BTN 28

































Reviews: