background image

This  INSTRUCTION  MANUAL, 
which  is  an  integral  and  indispen-
sable part of the product, must be 
delivered to the user by the installer 
and must be kept in a safe place for 
future  reference.  The  manual  must 
accompany  the  boiler  should  it  be 
sold or its possession transferred. 

The  boiler  must  be  used  for  the 
purposes  for  which  it  has  been 
intended. Any other use shall be 
considered  incorrect  and  there-
fore dangerous. 

The boiler must be installed in com-
pliance  with  applicable  laws  and 
standards  and  according  to  the 
manufacturer’s  instructions  given 
in this manual. Incorrect installation 
may cause injury to persons and/or 
animals  and  damage  to  property. 
The manufacturer shall not be held 
liable  for  any  such  injury  and/or 
damage. 

Damage  and/or  injury  caused  by 
incorrect  installation  or  use  and/or 
damage  and/or  injury  due  to  non-
observance  of  the  manufacturer’s 
instructions shall relieve the manu-
facturer from any and all contractual 
and/or extra-contractual liability. 

Before  installing  the  boiler,  check 
the technical data to be compatible 
with the requirements for its opera-
tion in the system.

Check that the boiler is intact and it 
has not been damaged during tran-
sport  and  handling.  Do  not  install 
equipment which is damaged and/
or faulty.

Do not obstruct the air suction and/
or heat dissipation openings. 

Only manufacturer-approved acces-
sories  and  optional  kits  are  to  be 
installed.

Properly  dispose  of  the  packaging 
as all the materials can be recycled. 
The  packaging  must  therefore  be 
sent to specific waste management 
sites. 

Keep  the  packaging  out  of  the 
reach of children as by its nature it 
may represent a hazard.

In the event of failure and/or faulty 
functioning, switch off the boiler. Do 
not attempt to repair it and contact 
a qualified service technician. 

Manufacturer-approved parts must 
be used for all repairs to the boiler. 

Non-observance  of  the  above 
requirements may affect the safety 
of the boiler and endanger people, 
animals and property.

The  manufacturer  recommends 
our  Customers  to  have  the  boiler 
serviced  by  an  Authorized  Service 
Centre. 

It is necessary to service the boi-
ler  periodically,  according  to  the 
schedule  indicated  in  the  appli-
cable section of this manual.
Correct  maintenance  allows  for 
efficient  and  correct  functioning 
of  the  equipment,  granting  the 
better  working  conditions,  opti-
mizing  performance  and  safety 
for  people,  animals,  things  and 
environment.

In  the  event  of  long  periods  of 
inactivity  of  the  boiler,  disconnect 
it from power mains and close the 
gas  tap  (Warning:  the  boiler  anti-
frost function is disabled).
Should  there  be  a  risk  of  freezing, 
add  antifreeze:  it  is  not  advisable 
to  empty  the  system  as  this  may 
result in damage; use specific anti-
freezing products suitable for multi-
metal heating systems.

        WARNING

This boiler has been built for installation in the country indicated 
on the technical data plate: installation in any other country may 
be source of danger for people, animals and property.

General informations for installers, service engineers and users

Summary of Contents for CAPRI C

























Reviews: