- 38 -
11
High temperature
protection
encoder board
temperature higher than
80
℃
Press and hold the pushbutton:
Blinking blinks ON_0.05/OFF_0.15
second
All pushbutton released: All lights are off
12
Normal operation
Press pushbutton
Green light flash ON_0.1/OFF_1.9 sec
9
9
.
.
R
R
E
E
C
C
E
E
I
I
V
V
E
E
R
R
I
I
N
N
S
S
T
T
A
A
L
L
L
L
A
A
T
T
I
I
O
O
N
N
9
9
.
.
1
1
P
P
r
r
e
e
p
p
a
a
r
r
a
a
t
t
i
i
o
o
n
n
f
f
o
o
r
r
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
1.
Required Tools for Receiver Installation:
(1)
Flat Head Screwdriver (-)
(2)
Phillips Head Screwdriver (+)
(3)
Multi-Meter
(4)
14mm Wrench x 2
(5)
Power Drill with
φ
10.5mm Drill-Bit
2.
Check to ensure that your receiver is not set to the same RF channel and ID code as any other
systems in operation at the same facility or within 300-meter distance.
3.
Prior to installation, make sure that the crane or equipment itself is working properly.
4.
Use a multi-meter to check the voltage source available and ensure the receiver voltage setting
matches your power source.
5.
Prior to installation, switch off the main power source to the crane or equipment.
9
9
.
.
2
2
S
S
t
t
e
e
p
p
B
B
y
y
S
S
t
t
e
e
p
p
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
a
a
n
n
d
d
C
C
o
o
m
m
m
m
i
i
s
s
s
s
i
i
o
o
n
n
i
i
n
n
g
g
9.2.1 Select the location
Select the location for installation and wiring: (
Attention!!!
)
α604/607/608
Systems
1.
For better reception, the location selected should have the antenna visible from all areas where the
transmitter is to be used.
2.
The location selected should not be exposed to high levels of electrical noise. Mounting the receiver
next to an unshielded variable frequency control (inverter) may cause minor interference. If it is
unavoidable, please consider using antenna with external coaxial cable to relocate the antenna to better
signal receipt position.
3.
Always locate the receiver unit as far away from high voltage wiring or equipment, such as: motor,
relay, magnetic valve, inverter controls and output cable
…
etc. as possible. Be sure to install the
receiver at least 2 meters away from the inverter. If the receiver is installed on the control box, then
the antenna position has to be higher than the control box. (as Fig.11)
α612
Systems
Drill four holes (dia.10.5mm) base on the position of the receiver shock absorbers. (Fig.12)
Summary of Contents for Alpha 600XJ Series
