background image

18 

Horizon Elite 1010/1410 Ice Machines (Remote Condensing)

Ice machine disposition

Possible causes

Corrective action

FLASHING

ON or OFF

Legend:

OFF

ON

6.  Ice machine is making ice. 

Excessive water in bin or 
coming into bin from transport 
tube.

1.  Failed water sensors. Processor 

assumes there is no water when 
there is water.

2. Blocked reservoir vent.
3. Defective water feed solenoid 

valve. Stuck in open position.

1.  Clean or replace water probe 

assembly. Check wiring  
connections.

2. Clean or replace vent tubes.
3. Replace water feed solenoid  

valve.

7.  Ice machine is not making ice. 

Lo water.

1.  Water supply is insufficient.
2. Low water pressure.
3. Defective water feed solenoid 

valve. Stuck in closed position.

4. No water feed output from  

PC board.

5. Plugged screen on inlet side of 

fill solenoid.

6. Plugged check valve.

1.  Restore water supply and check 

water filters. If evaporator was 
completely empty the reset button 
may have to be pressed to restart 
the ice machine.

2. Ice machine will eventually start 

when water reaches normal lo level.

3. Replace water feed solenoid valve.
4. Replace PC board.
5. Remove and clean screen.
6. Remove and clean.

 

ATTENTION!

To prevent circuit breaker overload, wait 5 minutes before restarting 
this unit. This allows the compressor to equalize and the evaporator 
to thaw.

Warranty Registration and Equipment Evaluation

Thank you for purchasing Follett equipment. Our goal is to earn your complete satisfaction by delivering high-value products and 
services backed by outstanding customer and technical support. 
Please review the installation instructions thoroughly. It is important that the installation be performed to factory specifications so 
your equipment operates at its maximum efficiency.
Follett LLC will not be liable for any consequential damages, expenses, connecting or disconnecting charges, or any losses 
resulting from a defect of the machine. For full warranty details, visit our website www.follettice.com/productwarranties.
Registering your equipments helps Follett track your equipment's service history should you need to contact us for technical 
support, and your feedback helps us improve our products and services. Please visit www.follettice.com/support to complete the 
Warranty Registration form.
Should you have any questions, please contact Follett's technical support group at (877) 612-5086 or 
(610) 252-7301 and we will be happy to assist you.

Summary of Contents for Horizon Elite 1010 Series





















Reviews: