background image

How unit works — SensorSAFE

models

When a container is placed within the actuation zone below the ice or water chute on the SensorSAFE dispenser
models, an invisible, randomly-generated infra-red signal is emitted, reflected off the container and detected by
the sensor. The sensor then sends a signal to the control board to activate the appropriate components to
dispense ice or water. LED’s on the board indicate when the board is receiving a signal from the sensors. 

A safety, shut-off feature automatically shuts off dispensing after one minute of continuous activation. Dispensing
can be restarted by moving the container away and then returning it to the actuation zone.

Dispensing can be temporarily suspended for cleaning by pressing and releasing the clean switch, located under
the left side of the top front cover. Pressing and releasing the button a second time will return the dispenser to
normal operation. If the button is not pressed a second time, the dispenser automatically resumes normal
operation (CLN LED goes out) after two minutes. An LED on the control board will light to indicate that dispensing
has been suspended by activation of the clean switch.

120 VAC

BLACK

BLACK

BLACK

BLACK

BLACK

BLACK

POWER

SWITCH

BIN LEVEL

BIN LEVEL

THERMOSTAT

SWITCH

RED

BROWN

WHITE

WHITE

WHITE

WHITE

WHITE

WHITE

WHITE

WHITE

PURPLE

CLEAN

SWITCH

ICE

GATE

SOLENOID

WHEELMOTOR

M

WTR

WTR

L1

PWR

L2

CLN

CLN

ICE

SOL WM

1

2

3

R1

RED

BIN SIGNAL

TO

ICEMAKER

S

S

ORANGE

WATER

SOLENOID

BLACK

BLK

R1

1

4
7

GRN

ICE

WTR

SENSOR

SENSOR

9

SensorSAFE dispensers

Summary of Contents for 110 Series





















Reviews: