background image

09

OPERATION

4-2. Sitting Down 

Attention : Lower yourself slowly to the lowest seated position! Risk of tipping over!

4-1-1.   To release the gas springs, you should first push forward the little latch to 
   

be found on the gas spring-release levers, then pull the release levers 

   

 themselves. (P32) 

4-1-2.   Having raised yourself up as for as your arms will allow, let go of the gas 
   

spring-release levers to lock the gas springs once more in place. (P33)

4-1-3.   Pull the two armrest-release levers, then lift the two armrests. Let go of 
   

the armrest-release levers and pull the two armrests up until they click in . 

  

(P34

&

35) 

4-1-4.   Repeats points 4-1-1. ~ 4-1-3. ( P32~35 ) until you are standing fully upright. 
   

The footrest should be in contact with the ground.

4-2-1.   To unlock the gas springs again, first push backward the little latch to be 
   

found on gas spring -release levers, then pull the release levers themselves  

   

(P32~35). Continue to hold down the release- levers as you use the armrests 

   

to pull yourself downwards.

4-2-2.   Let go of the gas spring- release levers and, making use of the armrest- 
   

release levers, lower the armrests (Fig-32~35) into their intermediate position.

4-2-2.   4-2-3. Repeat steps 4-2-1. and 4-2-2. ( Fig 32~35 ) until you are once again 
   

able to resume your seat.

By using the two armrest-release levers found further toward the front of the 
armrests, You can bring the armrests up to the appropriate height.

P32

P33

P34

P35

Summary of Contents for LLOYD LEO II













Reviews: