background image

SETUP AND OPERATION

 | ENGLISH

3.2  

WIRING 

All 

LC

 series loudspeakers are passive systems designed 

for use with external amplifiers. They have identical ca-
bling connectors and can be supplied with a choice of two 
options:

•  2 × 4 plastic terminal blocks are supplied as standard. 

These are suitable for wires with a cross section of up 
to 4 mm².

•  The loudspeakers can also be supplied with 2 × 4 ce-

ramic terminal blocks. These are suitable for wires with 
a cross section of up to 2.5 mm².

All cables used must be of an appropriate cross section. We 
recommend using ferrules for stranded wires.

A sealing plate is attached to each loudspeaker, along with 
two M16 cable glands.  Once cabling has been completed, 
this can be used to cover the connector panel and provide 
tension relief for the cable.
Please be aware of the fact that the specified degree of 
protection (in accordance with IEC 60529) is only obtained 
by mounting the sealing plate correctly. The cable glands 
are suitable for use with cables of between 6 and 10 mm 
in diameter.
If only one cable is being used, the other cable gland 
should be replaced by the dummy plug that has been sup-
plied with the loudspeaker.

Plastic terminals

Ceramic terminals

Cable outlet

21

Summary of Contents for LINEA LC Series















Reviews: