Fohhn - audio technologies
10
4.3 Controls
(Refer to illustrations on page 14 and 15)
All controls, inputs, and outputs of the EasyPort are located on the
loudspaker enclosure rear panel.
A sturdy carrying handle is integrated in the rear panel of the
enclosure.
1 recharge battery (FP1plus)
DC input jack for charging the integrated battery or operating
the EasyPort on AC power using the supplied AC adapter.
18 Power fuse (FP2plus only)
The power fuse is located below the power input socket. Prior
to replacing the power fuse unplug the FP2plus from power.
Make sure to use replacement fuse of the same type as the ori-
ginal fuse only (1A MTR (5x20mm)) for 230 VAC.
2 charging LED
This yellow LED will light constantly while the battery is being
charged and will start flashing as soon as the battery is fully
charged.
3 power switch
Switches power to the EasyPort audio section and amplifier on
and off but does not affect the charging circuit.
4 status LED
The status LED will light green to indicate the unit is on and the
battery adequately charged. It will change to red when the bat-
tery is down.
music
5 line input l/r
These two RCA jacks allow you to conect a CD player, casset-
te recorder, or other line level source to your EasyPort using a
stereo RCA cable (not supplied). The stereo input signal is inter-
nally summed to mono.
Input sensitivity is 100 mV into 10 k
Ω
for nominal level.
6 volume
This rotary potentiometer sets the loudness volume of the audio
source connected to the line input l/r jacks (5).
7 line out l/r
These two RCA jacks allow you to connect either a recorder or
another EasyPort to your unit using a stereo RCA cable (not sup-
plied).
The two jacks are internally paralleled and carry the output sig-
nal of the built-in mixer with all the volume and EQ settings you
made. The output voltage at nominal level is 0,5 V into 200
Ω
source impedance.
15 gain (FP2plus only)
This recessed pot matches the input level of the EasyPort to the
output level of an external audio source. You can only adjust
the gain control with the supplied small screwdriver so that the
control cannot be misadjusted inadvertently.
The gain control has been factory preset to a medium position.
wired mic
8 input
This balanced female XLR connector allows you to connect a
wired microphone (optional) via a standard microphone cable
with a male XLR connector (optional). Since the microphone
INPUT provides 12 V phantom power you can connect both
dynamic and electret or condenser microphones.
Input sensitivy for nominal level is 2 mV into 1 k
Ω
.
Pin 1 is ground, pin 2 „hot“ (inphase), pin 3 return.
9 volume
This rotary potentiometer sets the loudness volume of the
microphone connected to the INPUT connector (8).
16 gain (FP2plus only)
This recessed pot matches the input level of the EasyPort to the
output level of a wired microphone. You can only adjust the
gain control with the supplied small screwdriver so that the
control cannot be misadjusted inadvertently.
The gain control has been factory preset to a medium position.
wireless receiver
For details on the optional wireless receiver please refer to the
enclosed instruction manual for the receiver.
wireless mic
12 volume
This rotary potentiometer sets the loudness volume of the wire-
less microphone.
17 gain (FP2plus only)
This recessed pot matches the input level of the EasyPort to the
output level of a wireless microphone. You can only adjust the
gain control with the supplied small screwdriver so that the
control cannot be misadjusted inadvertently.
The gain control has been factory preset to a medium position.
EQ
FP1plus: The effective two-band equalizer is located in the signal
path immediately ahead of the power amplifier and therefore acts
on both the two microphone inputs and the line input.
FP2plus: The two-band equalizer acts on the microphone inputs
only.
13 bass
Rotary control for cutting or boosting the low frequencies.
14 treble
Rotary control for cutting or boosting the high frequencies.
Summary of Contents for EasyPort FP1 Plus
Page 16: ...110 006...
