•
DO NOT
use this appliance immediately below a fixed socket outlet.
•
DO NOT
use this appliance in the immediate vicinity of a bath, shower, swimming pool or other area where water/moisture could present a
hazard.
•
WARNING:
This heater is not equipped with a device to control the room temperature. Do not use this heater in small rooms when they
are occupied by persons not capable of leaving the room on their own, unless constant supervision is provided.
•
CAUTION
: This appliance must not be used in conjunction with any timer, programmer or thermal control, or any other device that will
switch on the appliance automatically, as a fire risk may occur if the heater is accidentally covered or displaced.
• Do not allow the heater to be covered as this may cause overheating. The appliance must not be placed near curtains or similar material. A
clearance space of at least one metre should be allowed in front of the appliance.
• The electrical socket that the appliance uses MUST be easily accessible. Do not route the supply cord directly in front of the heater unit.
• If the cord is damaged, it must be replaced by a service agent or competent person.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experi-
ence and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their
safety.
• Children should be supervised to ensure that they do not play with the appliance.
It is necessary for a suitable electrical socket to be located within a distance of 1.8 metres of the appliance in order that the prewired three pin
plug (13 amp fuse rated) can reach this point. The appliance is suitable for installation into all proprietary surrounds with an opening of 416mm
by 559mm (16” by 22”). The appliance is supplied fitted with 2 spacer frames enabling it to be fitted with no need for a recess into a wall or sur-
round back panel if both spacers are left attached to the fire. If the rear spacer only is removed then the mounting depth of the fire is 70mm.
Alternatively the appliance can be fully recessed if the opening depth is 120mm or greater both spacers are removed. It may be installed direct-
ly into any proprietary surround which can house this size of rebate, without the need to recess the appliance into a wall opening or fabricate
a false chimney breast. This appliance should be positioned on a firm level surface and in a clean ‘dust free’ environment. If the fire is to be sited
in a fire surround then the suitability of the surround for use with electrical heaters should be established with the fire surround manufacturer.
If fitted into an open draught fireplace, it is advisable to blank off the chimney to reduce the risk of draught through the fire, which may cause
the safety cut out system in the fan heater to operate.
Read
all
the instructions before continuing to unpack or install this appliance. Carefully remove the appliance from its packaging and lay on the
floor with it`s back surface downward. Note: DO NOT stand the appliance on its frame as this may cause distortion. Check that the remaining
packaging contents correlate with the component checklist below. Please dispose of all packaging with care at your local recycling centre.
QUANTITY
DESCRIPTION
1
Heater main body
1
Decorative fireframe (Blenheim, Traditional and Elegance models)
1
Fire front casting with ashpan door (Blenheim, Traditional and Elegance models)
1
Decorative fir integral front (Lulworth models only)
1
Orange coloured moulded fuel bed (Blenheim, Traditional and Elegance models)
1
White coloured moulded fuel bed (Lulworth models only)
1
Bag of overlay pebbles (Lulworth models only)
1
User instruction booklet
3
Neoprene securing strips
Section
Contents
Page No.
1.0
Important Notes
2
2.0
Installation Requirements
2
3.0
Appliance Data
2
4.0
Unpacking the Appliance
2
5.0
Component Checklist
2
6.0
Installing the Appliance
3
7.0
Fitting the Decorative Frame and Front
3
Section
Contents
Page No.
7.1
Fuel Bed (Lulworth Models Only)
3
8.0
Operating the Fire
3
9.0
Safety Cut-Out System
3
10.0
Maintenance
4
11.0
Cleaning
4
12.0
Spares
4
1.0 IMPORTANT NOTES
I N S TA L L AT I O N & U S E R I N S T R U C T I O N S
©
2012 Focal Point Fires plc.
2
GB IE
2.0 INSTALLATION REQUIREMENTS
3.0 APPLIANCE DATA
Supply Voltage:
230/240V AC, 50Hz
Fuse Rating:
13 Amp
Heating Elements: 2 x 900W/2 x1000W
Lighting:
Lulworth models : 1 x 60W “BC” bulb
All other models : 1 x 42W “BC” halogen lamp
4.0 UNPACKING THE APPLIANCE
5.0 COMPONENT CHECKLIST
