Focal Point ALVOR FULL DEPTH RADIANT Installation & User'S Instructions Download Page 1

INSTALLATION & USER INSTRUCTIONS

FULL DEPTH INSET GAS FIRE

1

Revision D - 03/13

© 2013 Focal Point Fires plc.

Focal Point Fires plc.

Christchurch, Dorset BH23 2BT

Tel: 01202 499330     

Fax: 01202 499326

www.focalpointfires.co.uk

e : [email protected]

GB IE

BS 7977-1 : 2009

BS EN 509 : 2000

KM579168

Questions or problems with your appliance?

Don’t take it back to the store

just give us a call on 

01202 588601

we’re here to help

lines open between 9am and 5pm, Monday to Friday

All instructions must be handed to the user for

safekeeping.

Please  note  :  Except  where  otherwise  stated,  all  rights,

including copyright in the text, images and layout of this

booklet is owned by Focal Point Fires plc.  You are not

permitted to copy or adapt any of the content without

the prior written permission of Focal Point Fires plc. 

IN THE UK ALWAYS USE A GAS SAFE REGISTERED ENGINEER TO INSTALL, REPAIR OR SERVICE THIS APPLIANCE

MODELS COVERED BY THESE INSTRUCTIONS

ALVOR FULL DEPTH RADIANT*

AURA FULL DEPTH RADIANT*

BLENHEIM FULL DEPTH RADIANT*

LULWORTH FULL DEPTH RADIANT*

SOHO FULL DEPTH RADIANT*

FINSBURY FULL DEPTH RADIANT*

ARCH FULL DEPTH RADIANT*

HORIZON FULL DEPTH RADIANT*

LANGHAM FULL DEPTH RADIANT*

AVAILABLE IN MANUAL, SLIDE CONTROL & REMOTE CONTROL

MODEL SHOWN : LULWORTH 

Summary of Contents for ALVOR FULL DEPTH RADIANT






















Reviews: