background image

www.fmuser.org 

www.fmuser.org 

 

19 

10.1 Lamp for Modulation Cell 

10.1.1 Lamp for Power on 

        When this lamp is luminous, it means the power supply for modulation cell is normal. 

10.1.2 Lamp for Video AGC 

        When video output is controlled by AGC, this lamp is light. 

10.2 Lamp for Amplifier Cell 

10.2.1 Lamp for Power on 

        When it is power on, the voltage of 5V is supplied normally, this green lamp is luminous. 

10.2.2 Lamp for RF 

      When the RF SWITCH on the main menu is set to “ON”, this green lamp is light. 

10.2.3 Lamp for Video 

        While output power is normal, this lamp is light. 

10.2.4 Lamp for REMOTE 

        In the page of Set, if Remote is enabled, this yellow light is illuminant. 

10.2.5 Lamp for TEMP 

        When  the  amplifier  temperature  is  higher  than  70

,  if  temperature  exceeds  85

,it  will 

power off immediately. 

10.2.6    Lamp for VSWR 

        If  reflected  power  is  higher  than  2%  of  rated  power,  the  lamp  is  light;  higher  than  4%  of 

power, it will decrease output power to decrease reflected power; when it is higher than 5%, it may 

happen that: the software power off the output, or the hardware circuit switch off the power supply, 

then power on again. 

10.2.7    Lamp for GENERAL 

        If  this  lamp  is  light,  it  may  happen  that:  forward  power  is  more  than  101%  of  rated  power, 

Summary of Contents for FU-300W





















Reviews: