FMT Swiss AG 23295 Operating Instructions Manual Download Page 2

Page: 2 / 24

Operating instructions for turbine flow meter

Contents

General details

______________________________________________________________________3

Intended use

1.1.

________________________________________________________________________3

Design and functional description

1.2.

______________________________________________________3

Display LCD

1.2.1.

_________________________________________________________________________4

User controls

1.2.2.

________________________________________________________________________4

Measuring chamber

1.2.3.

__________________________________________________________________5

Battery compartment

1.2.4.

_________________________________________________________________5

Technical data

1.3.

_______________________________________________________________________5

General safety instructions

____________________________________________________________6

Information on safety at work

2.1.

__________________________________________________________6

Signs and symbols used in the safety instructions

2.2.

__________________________________________6

Hazards when handling the turbine flow meter

2.3.

____________________________________________6

Assembly

___________________________________________________________________________6

Installation

_________________________________________________________________________7

Routine operation

___________________________________________________________________7

Output of liquid during standard operation (Normal Mode)

5.1.

__________________________________8

Resetting partial volumes

5.1.1.

_____________________________________________________________8

Resetting the resettable total volume (RESET TOTAL)

5.1.2.

________________________________________9

Output of liquid with display of current flow rate (Flow Rate Mode)

5.2.

____________________________9

Resetting partial volumes

5.2.1.

____________________________________________________________10

Calibration

________________________________________________________________________10

Definition

6.1.

_________________________________________________________________________10

Why calibrate the meter at all?

6.2.

________________________________________________________10

Calibration mode

6.3.

___________________________________________________________________11

Displaying the valid calibration factor - resetting the factory calibration factor (if necessary)

6.3.1.

______11

Calibration during simulated operation

6.3.2.

_________________________________________________13

Meter calibration during simulated operation

6.3.3.

____________________________________________13

Changing the K FACTOR directly

6.3.4.

_______________________________________________________15

Configuration of the turbine flow meter

_________________________________________________17

Service

____________________________________________________________________________18

Exchanging batteries

8.1.

________________________________________________________________18

Cleaning

8.2.

__________________________________________________________________________19

Troubleshooting

____________________________________________________________________19

Repairs/service

10.

_____________________________________________________________________20

Manufacturer‘s declaration

11.

___________________________________________________________20

Exploded drawingh

12.

_________________________________________________________________21

Summary of Contents for 23295

























Search results

Summary of Contents for 23295

Reviews:

Related manuals for 23295

Brands by name

Popular brands

FMT Swiss AG 23295, Operating Instructions Manual

Search results

Summary of Contents for 23295

Reviews:

Related manuals for 23295

Brands by name

Popular brands