background image

Transmitter and model setup

Before getting started, bind your receiver with your transmitter.

Please refer to your transmitter manual for proper operation.

CAUTION: To prevent personal injury, DO NOT install the propel-

ler assembly onto the motor shaft while testing the control  surfac-

es. DO NOT arm the ESC and do not turn on the transmitter until 

the Transmitter Manual instructs you to do so.

Tips: Make sure all control sticks on your radio are in the neutral 

position (rudder, elevator, ailerons) and the throttle is in the OFF 

position. Make sure both ailerons move up and down (travel) the 

same amount. This model tracks well when the left and right 

ailerons travel the same amount in response to the control stick.

Move the controls on the transmitter to make sure the aircraft 

control surface moves correctly. See diagrams right.

9

 Control throws

The suggested control throw setting for the Avanti are as follows (dual rate setting):

Tips: On the first flight, fly the model in low rate. 

The first time you use high rates,be sure to fly at 

low to medium speeds. High rate, as listed,  is 

only for EXTREME maneuvering.

EN

Ailer

on

Bank left

Bank right

Elev

at

or

Climb

Descend

St

eer
ing Rudder

Steer left

Steer right

17mm up / dowm

12mm up / dowm
10mm up / dowm
20mm left / right

15mm up / dowm
30mm left / right

Summary of Contents for 70MM AVANTI
















Reviews: