background image

1.Switch on transmitter, move throttle stick to top position, connect the battery pack to ESC

2.Wait for 2 seconds, the motor should emit special tone like "beep-beep-"

3.Wait for another 5 seconds, special tone like "♪56712" should be emitted, which means program mode is 

entered

.

EN

15

NO.1 Enter program mode

After entering program mode, you will hear 8 tones in a loop with the following sequence. If you move the throttle 

stick to bottom within 3 seconds after one kind of tones, this item will be selected.

You will hear several tones in loop. Set the value matching to a tone by moving throttle stick to top when you hear 

the tone, then a special tone "♪1515" emits, means the value is set and saved. (Keeping the throttle stick at top, 

you will go back to Step 2 and you can select other items; or moving the stick to bottom within 2 seconds will exit 

program mode directly) .

There are 2 ways to exit program mode:

1. In step 3, after special tone " ", please move throttle stick to the bottom position within 2 seconds.

2. In step 2, after tone "beep-----beep-----"(that is: The item #8),move throttle stick to bottom within 3 seconds.

Note: 1 long "beep-----" = 5 short "beep-"

NO.2 Select programmable items

NO.3 Set item value (Programmable value)

NO.4 Exit program mode

Note: Please make sure the throttle curve is set to 0 when the throttle stick is at bottom position and 100% 

for the top position.

Program the ESC with your transmitter (4 Steps)

Prompt tone

"beep"(1 short tone)
"beep-beep-"(2 short tone)
"beep-beep-beep-"(3 short tone)
"beep-beep-beep-beep-"(4 short tone)
"beep——"(1 long tone)
"beep——beep-"(1 long 1 short)
"beep——beep-beep-

"(

1 long 2 short

"beep——beep——"(2 long tone)

Selected item

brake

battery type
cutoff mode

cutoff threshold

startup mode

timing

set all to default

exit

Tones

"beep-"

1 short tone

"beep-beep-"

2 short tones

"beep-beep-beep"

3 short tones

Items
Brake
Battery type
Cutoff mode
Cutoff threshold
Start mode
Timing

Off

Lipo

Soft-Cut

Low

Normal

Low

On

NiMH

Cut-Off

Medium

Soft

Medium

High

Super soft

High

Summary of Contents for 70MM AVANTI
















Reviews: