background image

www.fmiproducts.com

126428-01B

15

For  propane/LP  units,  the  installer  must 

supply an external regulator. The external 

regulator will reduce incoming gas pressure. 

You must reduce incoming gas pressure to 

between 11" and 14" of water. If you do not re-

duce incoming gas pressure, heater regulator 

damage could occur. Install external regulator 

with the vent pointing down as shown in Figure 

12. Pointing the vent down protects it from 

freezing rain or sleet.

 CAUTION: Use only new, 

black  iron  or  steel  pipe.  Inter

-

nally-tinned copper tubing may 

be used in certain areas. Check 

your  local  codes.  Use  pipe  of 

1/2" diameter or greater to allow 

proper gas volume to heater. If 

pipe is too small, undue loss of 

volume will occur.

Propane/LP 

Supply Tank

External 

Regulator 

with Vent 

Pointing 

Down

Figure 12 - External Regulator With Vent 

Pointing Down

INSTALLATION

Continued

  WARNING:  Use  pipe  joint 

sealant that is resistant to liquid 

petroleum (LP) gas.

We recommend that you install a sediment 

trap in supply line as shown in Figure 13. 

Locate sediment trap where it is within reach 

for cleaning. Install in piping system between 

fuel supply and heater. Locate sediment trap 

where trapped matter is not likely to freeze. 

A sediment trap traps moisture and contami-

nants. This keeps them from going into heater 

controls. If sediment trap is not installed or is 

installed wrong, heater may not run properly.

 CAUTION: Avoid damage to 

gas  control.  Hold  gas  control 

with wrench when connecting it 

to gas piping and/or fittings.

Installation must include an equipment shutoff 

valve, union and plugged 1/8" NPT tap. Locate 

NPT tap within reach for test gauge hook up. 

NPT tap must be upstream from heater (see 

Figure 13).

IMPORTANT:

 Install equipment shutoff valve 

in an accessible location. The equipment 

shutoff valve is for turning on or shutting off 

the gas to the appliance.
Check your building codes for any special 

requirements for locating equipment shutoff 

valve to fireplaces.

Apply pipe joint sealant lightly to male NPT 

threads. This will prevent excess sealant from 

going into pipe. Excess sealant in pipe could 

result in clogged heater valves.

  Pipe  Cap Tee

 Nipple    Joint

*  Purchase the optional equipment shutoff 

valve from your dealer.

**Minimum inlet pressure for purpose of input 

adjustment. 

Figure 13 - Gas Connection

Gas 

Control 

3" Minimum

Sediment Trap

Equipment Shutoff Valve 

With 1/8" NPT Tap*

Approved Flexible 

Gas Hose (if 

allowed by local 

codes)

PROPANE/LP

 

From External 

Regulator

(11" W.C.** 

to 14" W.C. 

Pressure)

NATURAL

 

From Gas 

Meter

(5" W.C.** 

to 10.5" 

W.C. 

Pressure)

Summary of Contents for FVFC24NR

































Reviews: