background image

 

8

MANTELS: 

A mantel may be installed if desired (see figure 24). 
Woodwork such as wood trims, mantels, or any other 
combustible material projecting from the front face must not 
be placed within 9 inches of the fireplace opening. 
Combustible materials above 9 inches and projecting more 
than 1 -1/2 inches from the fireplace face must not be placed 
less than 12 inches from the top of the opening of the fireplace 
(NFPA STD 211, Sec. 7-3.3.3). 
 
 

 

 

Mantels or any other combustible materials also may come up 
to the side periphery of the black metal face of the fireplace as 
long as the projection from the front face falls within the limits 
depicted in figure 25.  

 
 

 
 
 
 
 
 
 
 
 

WARNING:

  Risk of fire; Replace grate with FMI Model 

36E GR grate only. 

 
DAMPER OPERATION: 

The damper handle to open and close the damper blade is 
located inside the firebox at the center towards the back wall.  
Pushing the handle back in the keyway slot will free the 
damper blade to automatically open.  To close, reach in and 
push the handle back into the keyhole slot then pull down and 
forward to lock it in place (see figure 26). 
 

WARNING:

 Damper handle will remain hot even after there 

is no fire in the fireplace.  Make sure it cools down before 
touching the handle. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
FOR FURTHER OPERATING GUIDELINES, 
INSTRUCTIONS AND WARRANTY INFORMATION 
PLEASE REFER TO YOUR HOMEOWNERS GUIDE OR 
CONTACT YOUR AUTHORIZED DEALER. 
 

 
 
TECHNICAL SERVICE 

 
You may have further questions about installation, operations, 
or troubleshooting.  If so, contact FMI/DESA International’s 
Technical Service Department at 1-888-427-8322.  When 
calling FMI/DESA International, have the model number of 
your fireplace ready. 
 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Figure 24 

 
 
 
 
 
 
 
 
 

 
 

 
 
 
Figure 25

 

 
 
 
 
 
 
 
 
 
 
 
 
 

 
Figure 26

 

Summary of Contents for 36ECD











Reviews: