Flyzone DHC-2 BEAVER Instruction Manual Download | Manualshive

Page: 5 / 20

background image

5

ASSEMBLY

NOTE:

This instruction manual applies to all versions

of the DHC-2 Beaver (Rx-R, Tx-R, and RTF), simply skip
the steps that do not apply.

Mount the Landing Gear

❑

1. Use a #2 Phillips screwdriver to fasten both main landing

gears to the fuselage with three M3x16 screws in each side.

❑

2. Mount the tail gear with two M2.5x8 screws, then fasten

the pushrod wires as shown. Make sure the tail wheel is
perpendicular with the steering arm and tighten the screws.

Mount the Floats

❑

1. Connect the fl oats to each other with the horizontal

struts and four M2.5x20 machine-thread screws.

«
...
3
4
5
6
7
...
»

Summary of Contents for DHC-2 BEAVER





















Reviews:

No comments

Related manuals for DHC-2 BEAVER

Brand: Fisher-Price Pages: 16

Brand: Ozone Pages: 20

Brand: Eduard Pages: 4

Brand: MTHTrains Pages: 36

Brand: Dancing Wings Hobby Pages: 6

Brand: GAME OF BRICKS Pages: 32

Brand: Kalee Pages: 6

Spitfire F.Mk.22/24

Brand: Eduard Pages: 5

Brand: GREAT PLANES Pages: 50

Premier 2-8-8-8-2 Triplex

Brand: M.T.H. Pages: 28

Brand: Enabling Devices Pages: 2

Lava Launch Coaster 50050

Brand: K'Nex Pages: 72

Brand: H-KING Pages: 11

Brand: E sky Pages: 140

Brand: PBS KIDS Pages: 49

CVN-65 Enterprise Part4

Brand: Eduard Pages: 8

TWISTER Rave Hoopz

Brand: Hasbro Gaming Pages: 2

Nano Warbirds P-47

Brand: J-Power Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands