background image

5101571-03

If any part is found to be defective due to faulty manufacture within
the guarantee period, Husqvarna UK Ltd., through its Authorised
Service Repairers will effect the repair or replacement to the cus-
tomer free of charge providing:
(a) The fault is reported directly to the Authorised Repairer.
(b) Proof of purchase is provided.
(c) The fault is not caused by misuse, neglect or faulty adjustment

by the user.

(d) The failure has not occurred through fair wear and tear.
(e) The machine has not been serviced or repaired, taken apart or tam-

pered with by any person not authorised by Husqvarna UK Ltd..

(f)  The machine has not been used for hire.
(g) The machine is owned by the original purchaser.
(h) The machine has not been used commercially.
*

This guarantee is additional to, and in no way diminishes the
customers statutory rights.

Failures due to the following are not covered, therefore it is important
that you read the instructions contained in this Operator's Manual

and understand how to operate and maintain your machine:
Failures not covered by guarantee
* Replacing Nylon Line.
* Failures as a result of not reporting an initial fault.
* Failures as a result of sudden impact.
* Failures as a result of not using the product in accordance with the in-

structions and recommendations contained in this Operator's Manual.

* Machines used for hire are not covered by this guarantee.
* The following items listed are considered as wearing parts and

their life is dependent on regular maintenance and are, therefore
not normally subject to a valid warranty claim: Nylon Line, Spool
and Line, Electric Mains Cable

* Caution!

Husqvarna UK Ltd. does not accept liability under the warranty
for defects caused in whole or part, directly or indirectly by the
fitting of replacement parts or additional parts that are not either
manufactured or approved by Husqvarna UK Ltd., or by the ma-
chine having been modified in any way.

Guarantee & Guarantee Policy

EC Declaration of Conformity

Husqvarna UK Ltd., Aycliffe Industrial Park
Newton Aycliffe, Co. Durham, DL5 6UP,  England

Declare under our sole responsibility that the product(s);

Category............................Electric Lawn Trimmer
Type(s)

............................PTXT25

Identification of Series.......See Product Rating Label
Year of Construction..........See Product Rating Label

Conforms to the essential requirements & provisions of the following EC Directives:
98/37/EC (until 31.12.09),  2006/42/EC (from 01.01.10),  2004/108/EC,  2000/14/EC
based on the following EU harmonized standards applied:
EN60335-1, EN60335-2-91, EN786, EN50366, EN55014-1, EN61000-3-2, EN61000-3-3

The maximum A weighted sound pressure level L

pA

at the operator’s position, recorded on a sample of the above prod-

uct(s) corresponds to the Level given in the table.

The maximum hand / arm vibration weighted value measured according to EN ISO 5349 on a sample of the above
product(s) corresponds to the Value given in the table.

2000/14/EC: The Measured Sound Power L

WA

& Guaranteed Sound Power L

WA

values are according to the tabulated figures.

Conformity Assessment Procedure...............

Annex VI

Notified Body.................................................

Intertek, Cleeve Road
Leatherhead, Surrey
KT22 7SB, England

Newton Aycliffe  03/03/2009
M.Bowden
Research & Development Director
Husqvarna UK Ltd.
Keeper of technical documentation

Type

Width of Cut (cm)

Speed of Rotation of Cutting Device (rpm)

Power (W)

Measured Sound Power L

WA

(dB(A))

Guaranteed Sound Power L

WA

(dB(A))

Level (dB(A))

Value (m/s

2

)

Weight (Kg)

PTXT25

25

10,750

500

93

96

77

1.74

3.6

• Awareness of the environment must be considered when dis-

posing of ‘end-of-life’ product.

• If necessary, contact your local authority for disposal informa-

tion.

The symbol            on the product or on its packaging indicates that this
product may not be treated as household waste.  Instead it shall be handed
over to the applicable collection point for the recycling of electrical and elec-
tronic equipment.

By ensuring this product is disposed of correctly, you will help prevent po-

tential negative consequences for the environment and human health,
which could otherwise be caused by inappropriate waste handling of this
product.
For more detailed information about recycling of this product, please con-
tact your local council office, your household waste disposal service or the
shop where you purchased the product.

Environmental Information

Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice.

Copyright © 2008 Flymo S.A. All rights reserved.  Flymo® and other product and feature names are registered or unregistered trademarks

of Flymo S.A.

Husqvarna UK Ltd.

Aycliffe Industrial Park

NEWTON AYCLIFFE

Co.Durham  DL5 6UP

ENGLAND

Telephone - 01325 302302  Fax - 01325 310339

Summary of Contents for Power Trim 500 XT










Reviews: