FLYING MOLE CORPORATION
5199-1 Waji-cho, Hamamatsu 431-1115 Japan.
Tel : +81-53-486-6030 Fax : +81-53-486-6033
http://www.flyingmole.co.jp [email protected]
This document is printed with soy ink
(an organic ink made from soy oil) on
recycled paper. Environmentally
friendly printed matter.
Questionnaire
8
There is a questionnaire in the
“Support”
section in our website.
This is for helping us serve you better by developing new products.
We look forward to your access to the following URL.
http://www.flyingmole.co.jp
FP40781-000
Privacy Policy
Security of Collected Information
We maintains strict physical, electronic, and administrative safeguards to protect
your personal information from unauthorized or inappropriate access. We
restricts access to information about you to who need to know the information to
respond to your inquiry or request. Who misuse personal information are subject
to disciplinary action.
Maintenance
Never use liquids such as benzine, thinners,
etc., chemically treated cloths, and do not spray
any aerosol type insecticides on the amplifier.
Clean the case using only a soft, dry cloth.
If the amplifier becomes soiled, mix a solution
of water and a neutral detergent then dampen
a soft cloth in the solution, wring out as much
of the solution as possible, and clean the am-
plifier. Then use a soft, dry cloth to wipe the
surface dry.
Soft cloth
Neutral
detergent
Benzine
Liquids
7
Dimensions
6
254 (10”)
11
(7/16”)
13
(1/2”)
277 (10-7/8”)
281 (11-1/16”)
54
(2/1/8”)
60
(2-3/8”)
6
(1/4”)
Connections
4
CD Player, etc.
Memory Player, etc.
HDD Recorder, etc.
Power Amplifier (2 channel)
LINE IN Jacks
(for recording analog sounds)
LINE IN Jacks
BALANCE IN Jacks
LINE OUT
Jacks
LINE OUT
Jacks
Stereo LINE OUT
Jack
Speaker
AC Power Cable
Pin Jack Cable
XLR Cables
Connect to AC Outlet
Speaker
or
(*1)
(*1)
XLR cables can be used if the power
amplifier to be connected has BAL-
ANCE INPUT jacks.
The signal arrangement of the BAL-
ANCE OUTPUTS on this products is:
1: GND,
2: HOT,
and
3: COLD
●
Connection of the REMOTE POWER CONTROL Trigger
By connecting the REMOTE POWER CONTROL Trigger, the activation/deactivation of power on a Flying
Mole power amplifier equipped with REMOTE POWER CONTROL Trigger Input can be interlocked with the
activation/deactivation of power on this device. Refer to the owner’s manuals of the devices to be connected
as well before connecting cables.
1
. Remove the attachment to the REMOTE POWER CONTROL connectors.
2
. Remove insulation material around the ends of the supplied remote con-
nection cables and twist the wires until they are stranded securely.
3
. Insert the wires into the holes in the attachment and tighten the screws
to fix the cables.
(Be sure to check polarity before connection)
*
Treat the other ends of the cables (power amplifier side) as in the steps
1
to
3
above. (Remove the connectors attached to the power amplifier.)
4
. Plug the attachement back to the REMOTE POWER CONTROL con-
nector and connect the other end to the power amplifiers.
*
Commercially available vinyl insulated cables can be used as well.
• Compatible cable type is AWG24 to AWG12.
Refer to the steps
1
through
4
above when connecting cables and make
sure that the polarity is correct.
L
L
L
Speaker (L)
Speaker (R)
Tweeter
Midrange
Woofer
Tweeter
Midrange
Woofer
Pin Jack Cable
Pin Jack Cable
Pin Jack Cable
Pin Jack Cable
Pin Jack Cable
Pin Jack Cable
LINE IN Jack
LINE IN Jack
LINE IN Jack
LINE IN Jack
LINE IN Jack
LINE IN Jack
HIGH
MID
LOW
HIGH
MID
LOW
Power Amplifier
(1 channel)
Power Amplifier
(1 channel)
Power Amplifier
(1 channel)
Power Amplifier
(1 channel)
Power Amplifier
(1 channel)
Power Amplifier
(1 channel)
*
Refer to the “
Connection Example 1
” for connection to INPUT jacks and AC IN jacks.
Connection Example 2: Bi-amp connection
■
Connecting Devices
●
Make sure the power of all related equipments is turned off, when wiring and checking their polarity.
●
Make sure that the cable is not shorted, when connecting the speaker cable.
●
Connect the power cable after all connections are complete.
●
This product should be placed close to the main source of electrical power (wall outlet in your house)
and keep the power plug within reach.
●
Connectors names may be different from this manual.
✱
Refer to the owner's manuals of the equipments to be connected as well.
* Be sure to check polarity before
connection.
Connect the black cable to the
negative terminal.
Supplied remote
connection cable
+
–
Connection Example 1: Common setting for playing stereo sounds
Specifications
5
Total Harmonic Distortion
0.01% (5Hz – 100kHz)
Frequency Response
DC – 20kHz (+0dB / –0.2dB)
S/N Ratio
100dB (IHF-A)
Input Sensitivity / Input Impedance
150mV / 10k
Ω
Output Level / Output Impedance
1V / 1k
Ω
Power Consumption
7W (AC 120V model) , 8W (AC 230V model)
Power Supply
AC 120V 60Hz (U.S.A. & Canadian model) / AC 230V 50Hz
Use Environment
0
°
C – 40
°
C
Max. Dimensions inch / mm
11–1/16”(W) x 2–3/8”(H) x 10–7/8”(D) mm / 281(W) x 60(H) x 277(D) mm
Weight
3.8 kg (8.4 lbs)
* Nameplate is on the bottom of the product.
* Due to product improvement, specifications and/or product design are subject to change without notice.
Unit
: mm (”)
