Flycam 5000 Assembly Manual Download

Page: 2 / 11

Head Plate

Bottom Plate

Mid Plate

Head Assembly (These three individual pieces are shipped as one assembled unit)

Quick release
plate

Quick release
adapter

Lever to remove /
attach the quick release

Unico Quick Release Adapter

1X 19mm Adapter

1X 22mm Adapter

NOTE:

A locking pin located at the front prevents camera rotation

Table Clamp

Storage Bag

Safety Hints

ATTENTION: PLEASE READ THIS BEFORE USING TO PREVENT SERIOUS DAMAGE TO THE GEAR!

BE HIGHLY VIGILANT OF SURROUNDINGS

Check the area you will be shooting in, before hand. Make sure your path is clear. Look for obstacles and
note anything you might run into or trip over. Extra care is also necessary when tackling stairs and other
kinds of uneven ground.

ALWAYS WEAR PROTECTIVE GEAR

If you intend to shoot while moving fast or while traversing uneven terrain, do not hesitate to wear

protective gear as knee or elbow pads, or a helmet.

DO NOT SHOOT IN UNSAFE CONDITIONS

Avoid situations where one commonly falls like skis, skates or running in muddy fields.

Summary of Contents for 5000












Search results

Summary of Contents for 5000

Reviews:

Related manuals for 5000

Brands by name

Popular brands

Flycam 5000, Assembly Manual

Search results

Summary of Contents for 5000

Reviews:

Related manuals for 5000

Brands by name

Popular brands