The sub trims function individually adjusts the center position of each servo of the
4 channels. This is particularly useful when the servo mechanics doesn’t allow an
adjustment fine enough.
Touch the channel which sub trim must me adjusted
Use the wheel to move the red needle and modify the sub trim value of the
selected channel.
The position of the corresponding channel is displayed in real time
In this example, the channel 2 (throttle) has been selected and the throttle
trigger is half braking.
The sub trim of each channel can be assigned to a trim switch.
记忆微调功能可分别调节4个通道舵机的中位。当舵机调节不能满足需要时，该功能的
调节作用就尤为明显。
点触通道即可进行记忆微调
用转轮移动红色指针来调节所选择通道的记忆微调数值。
相关通道位置即时呈现。
如图所示： 2通道（油门通道）被选中，油门扣机处于50%刹车状态。
每个通道的记忆微调可分配给一个微调开关来控制。
The steering exponential function modifies the transfer curve between
the steering wheel and the channel 1.
Once activated, 2 buttons select which parameter value to modify:
Rate
: adjust the slope of the curve. The smaller is the slope, the shorter
is the throw of the corresponding servo.
Exp
.: adjust the linearity of the curve. A value of 0 corresponds to a
perfectly linear curve. A positive value decreases the sensitivity near
the neutral position and increases it on the extreme sides. A negative
value increase the sensitivity near the neutral position and decreases
it on the extreme sides The vertical dotted line displays in real time the
position of the steering wheel.The horizontal dotted line displays in
real time the steering position after the exponential function.
In this example, the exponential function is activated, the selected
parameter is exponential and is set to its maximum value.
The horizontal dotted line shows a steering wheel 20% under the
neutral position
but the horizontal dotted line indicates that the resulting servo throw is
less than 10% showing the efficiency of the exponential function.
The activation of the steering exponential function can be assigned to
a push button.The steering rate can be assigned to a trim switch
The steering exponential can be assigned to a trim switch.
方向指数功能调节方向舵和1通道之间的转换曲线。
该功能一旦被激活，则有2个按钮用来选择需要修正的参数数值。
比率
：该功能用于调整曲线的倾斜度。倾斜度越小，对应的舵机的抛物线越短。
曲线
：该功能用于调节曲线的线性。数值是0时，曲线是线性的。正值会减少中位附近
的灵敏度，增加两端的灵敏度。负值则增加中位附近的灵敏度，减少两端的灵敏度。
垂直方向的点线显示方向舵的即时位置。
水平方向的点线显示指数功能调整后的方向舵的位置。
如图所示：指数功能被激活，选定的参数是指数参数，并被调到最大值。
竖直方向的点线表示方向在中位以下20%的位置，在这种设定下舵机在中位以下不到
10%的位置，舵机位置由水平方向的点线表示。
方向指数功能的开启或关闭可分配给一个按键来控制。
方向比率功能可分配给一个微调开关来控制。
方向指数功能可分配给一个微调开关来控制。
17.03:
Sub trims
记忆微调
17.04:
Steering exponential
方向指数
22
http://www.flysky-cn.com
