EN
GLISH
11
Troubleshooting
If the LED Strip Light does not turn on, please proceed as follows:
PROBLEM
CAUSE
SOLUTION
The lighting is
not working
Missing connection of the LED Driver to the power outlet Connect the LED Driver to the power outlet
Missing connection of the lighting unit to the LED Driver Connect the lighting unit to the LED Driver with its con-
nector
If the problem is not solved after following the above, please contact your Hagen retailer.
ROMA LED STRIP LIGHT IDENTIFICATION CODES
AQUARIUM MODEL
ROMA 90
ROMA 125
ROMA 200
ROMA 240
LED STRIP LIGHT UNIT
BT Led Unit Roma 90
BT Led Unit Roma 125
BT Led Unit Roma 200
BT Led Unit Roma 240
LED STRIP LIGHT MODEL
A13291
A13292
A13293
A13294
LUMINAIRE WATTAGE
12.5W
16.5W
21W
24W
LUMENS
1000lm
1300lm
1600lm
1950lm
LUMINAIRE OPERATING VOLTS
24Vdc
24Vdc
24Vdc
24Vdc
LED DRIVER TYPE
S012BE [X] 2400050
S018BA[X] 2400063
S024AM[X] 2400100
S024AM[X] 2400100
LED DRIVER INPUT VOLTS
100-240 Vac
100-240 Vac
100-240 Vac
100-240 Vac
X = B FOR UK PLUG X = V FOR EU PLUG X = U FOR US PLUG
VICENZA and VENEZIA LED STRIP LIGHT IDENTIFICATION CODES
AQUARIUM MODEL
VICENZA 180
VICENZA 260
VENEZIA 190
VENEZIA 350
LED STRIP LIGHT UNIT
BT Led Unit Vicenza 90
BT Led Unit Vicenza 260 BT Led Unit Venezia 190
BT Led Unit Venezia 350
LED STRIP LIGHT MODEL
A13296
A13297
A13298
A13300
LUMINAIRE WATTAGE
26W
48W
26W
16.5W+37W
LUMENS
2200lm
4000lm
2200lm
3100lm
LUMINAIRE OPERATING VOLTS
24Vdc
24Vdc
24Vdc
24 Vdc
LED DRIVER TYPE
S024AM[X] 2400100
S050F[X] 2400200
S024AM[X] 2400100
S018BA[X]2400063 (A13299) +
S040Q[X] 2400150 (A13300)
LED DRIVER INPUT VOLTS
100-240Vac
100-240Vac
100-240Vac
100-240Vac
X = B FOR UK PLUG X = V FOR EU PLUG X = U FOR US PLUG
LED STRIP LIGHT AND TANK MAINTENANCE
Cleaning the LED Strip Light
Disconnect the Strip Light from power supply before any maintenance operation
.
WARNING: Be sure you unplug the LED driver from the power outlet; just switching off the
lights with the APP is NOT enough because it does not stop the power supply. Never place the
LED Strip Light under water jets or submerge in water
.
No special maintenance is required for the Fluval LED Strip Light and Canopy, other than periodic cleaning with a damp
cloth (never use harsh chemical products or detergents). To remove calcareous deposits, it is recommended to use a mild
acid such as lemon juice, followed by a thorough wipe down with a damp cloth to remove any residue.
Saltwater aquariums
It is commonly known that salt water is far more corrosive, conductive (of electricity) and generally degrades both plastic
and metal parts at an accelerated rate versus fresh water. To minimize salt accumulations on the Fluval Canopy and on the
LED Strip Light, it is recommended to take note of the following helpful tips:
1. Make sure filter outputs do not spray above the water surface, position them below the water surface with a slight
downward angle, but still allow for surface movement (contributes to oxygenation).
2. If an air pump must be used, frequent removal of salt deposits will be necessary.
3. Keep the water level as constant as possible (regular top-ups due to evaporation). This is beneficial in providing stable
salinity and will help protect the canopy.
4. It is recommended to regularly clean all LED Strip Light components and the Canopies that come into contact with salt
water at least every 15 days. The cleaning should be carried out with a wet cloth (never use harsh chemical products
or detergents). Simple lemon juice may be used to take away salt accumulation. Afterwards rinse carefully to eliminate
every residue of acid.
REPLACEMENT PARTS
Always use genuine Fluval Spare Parts to guarantee continued performance and safety
.
For a full listing of replacement parts please visit
www.fluvalaquatics.com
.
