1
2
BATTERY REMOVAL AND INSTALLATION INSTRUCTIONS
1
Open the battery door with a philips screwdriver (not
included).
2
If used or spent batteries are present, remove these
batteries from the unit by pulling up on one end of each
battery. Install 6 new AA (LR6) alkaline batteries (not
included) as shown in the polarity diagram (+/-) inside
the battery compartment. Do not use a metal tool to
remove the batteries.
3
Replace battery door securely. Check your local laws
and regulations for correct recycling and/or battery
disposal.
Contains 1 x 3.7V LiPo battery pack. Requires 6
x 1.5V AA (LR6) alkaline batteries (not included).
Batteries
or battery packs must be recycled or disposed of
properly. When this product has reached the end
of its useful life it should not be disposed of with
other household waste. The Waste Electrical and Electronic
Equipment Regulations require it to be separately collected
so that it can be treated using the best available recovery and
recycling techniques. This will minimize the impact on the
environment and human health from soil and water
contamination by any hazardous substances, decrease the
resources required to make new products and avoid using
up landfill space. Please do your part by keeping this product
out of the municipal waste stream! The “wheelie bin” symbol
means that it should be collected as “waste electrical and
electronic equipment”. You can return an old product to your
retailer when you buy a similar new one. For other options,
please contact your local council.
Battery Safety Information:
Contains 1 x 3.7V LiPo battery pack.
Requires 6 X1.5V AA (LR6) alkaline batteries (NOT
INCLUDED).
Batteries are small objects.
Replacement of batteries must be done by adults.
Follow the polarity (+/-) diagram in the battery compartment.
Promptly remove dead batteries from the toy.
Dispose of used batteries properly.
Remove batteries for prolonged storage.
Only batteries of the same or equivalent type as
recommended are to be used.
• DO NOT incinerate used batteries.
• DO NOT dispose of batteries in fire, as batteries may
explode or leak.
• DO NOT mix old and new batteries or types of batteries
(i.e. alkaline/standard).
• DO NOT use rechargeable batteries.
• DO NOT recharge non-rechargeable batteries.
• DO NOT short-circuit the supply terminals.
Trouble Shooting:
If normal function of the product is disturbed or interrupted, strong
electro-magnetic interference may be causing the issue. To reset
product, turn it completely off, then turn it back on. If normal
operation does not resume, move the product to another location
and try again. To ensure normal performance, change the batteries,
as low batteries may not allow full function.
This product complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interferencereceived, including interference that may cause undesirable operation.
This equipment has been tested and found to comply with the limits for Class B digital devices to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference to radio communications. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio
communication. If this toy does cause interference to radio or television reception (you can check this by turning the toy off and on while
listening for the interference), one or more of the following measures may be useful: • Reorient or relocate the receiving antenna • Increase
the separation between the toy and the radio or the TV • Consult the dealer or an experienced TV-radio technician for help.
NOTE: Changes, adjustments or modifications to this unit, including but not limited to, replacement of any transmitter component (crystal,
semiconductor, etc) could result in a violation of FCC rules under part 15 and/or 95 and must be expressly approved by Spin Master Ltd or
they could void the user’s authority to operate the equipment.
LiPo BATTERY INSTRUCTIONS
• Never charge battery unattended. • Charge battery in isolated
area. Keep away from flammable materials.
• Do not expose to direct sunlight. • There is a risk of the batteries
exploding, overheating, or igniting. Do not disassemble, modify
heat, or short-circuit the batteries. Do not place them in fires or
leave them in hot places. • Do not drop or subject to strong
impacts. • Do not allow the batteries to get wet. • Only charge the
batteries with the specified Spin Master™ battery charger. • Only
use the batteries in the device specified by Spin Master™.
• Carefully read the instruction guide, and use the batteries
correctly. • In the unlikely event of leakage or explosion use sand
or a chemical fire extinguisher for the battery.
• Batteries must be recycled or disposed of properly.
Product Battery Removal Instructions:
Internal battery is factory installed, product disassembly and
battery removal must be performed by an adult. Do not puncture,
cut, tear, compress or deform product during disassembly. Ensure
product is turned off, then use a screw driver to remove all screws.
Separate product body halves to expose internal electronics. When
battery is visible in its entirety use scissors to cut a single battery
wire, immediately wrap the cut wire end with tape to isolate it,
repeat until all battery wires are cut and isolated, and the battery is
free from the rest of the product. Dispose of battery in accordance
with your local battery recycling or disposal laws.
NOTE:
Opening
of product and/or removal of battery will render product inoperative
and voids manufacturer warranties, dispose of remaining product
components in accordance with local laws.
2
