background image

DC Inverter U-match Series Floor Ceiling Type Unit 

45 

3.4 Check after Installation 

Check Items after Installation 

Check items

 

Possible  events  due  to  improper 

insta

l

lation

 

Is the main body installed securely?

 

The  unit  may  fall  down,  vibrate  or 

produce noise.

 

Did you do water leakage test?

 

Cooling  capacity  may  become 

unsatisfactory.

 

Is the unit well insulated from heat?

 

Condensate, water drops may occur.

 

Does water drainage go well?

 

Condensate, water drops may occur.

 

Is  the  voltage  consistent  with  that  stated 

on the nameplate?

 

The  unit  may  fail  or  its  components 

may get burned.

 

Are  the  wires  and  pipes  installed 

correctly?

 

The  unit  may  fail  or  its  components 

may get burned.

 

Has the unit been safely grounded?

 

Risk of electric leakage.

 

Do the specifications of wires comply with 

the requirement?

 

The  unit  may  fail  or  its  components 

may get burned.

 

Is there any obstacle blocking the air inlet 

and outlet of the indoor or outdoor units?

 

Cooling  capacity  may  become 

unsatisfactory.

 

Have  you  recorded  the  length  of 

refrigerant  pipe  and  the  refrigerant 

charging amount?

 

The refrigerant charging amount can’t 

be controlled.

 

3.5 Test Running 

Preparation before connecting the power. 

(1)  Power must not be connected if the installation work is not completed.   
(2)  Control circuit is correct and all the wires are firmly connected.   
(3)  Cut-off valves of the gas pipe and liquid pipe are open.   
(4)  The inside of the unit should be clean. Take irrelevant objects out if there is any.   
(5)  After checking, re-install the front side plate.   

Operation after connecting the power. 

(1)  If all the above works are finished, power on the unit. 
(2)  If the outside temperature is more than 30

, heating mode can’t be enabled.   

(3)  Make sure the indoor and outdoor units can run normally.   
(4)  If there’s sound of liquid shock when the compressor is running, then stop the 

air conditioner immediately. Wait until the electric heating belt is heated enough, 
and then restart the air conditioner.   

(5)  Feel the air flow of the indoor unit to see if it is normal.   

Summary of Contents for FGC-121EI/1JA-N3





































































Reviews: