background image

5

Physical Characteristics

Figure 3. Voice Controls

TS22A Speakerphone and Speaker Monitor 
Modes

See Figure 3.

The TS22A speakerphone feature lets you carry on a 
conversation hands-free. This increases safety when 
working on ladders or in congested areas where the 
restriction of line cords may cause a hazard. 

The SPEAKER button controls the volume in 
speakerphone and speaker modes. Speakerphone and 
speaker modes have three volume levels (low, medium, 
and high).

The speaker may be turned on in MONITOR mode.

Speakerphone mode may be used only in TALK mode. 
With the speakerphone on, pressing the MUTE button 
turns off the speakerphone microphone for privacy. 

A call may be initiated with the speakerphone on or off 
by moving the TALK/ MONITOR switch to the TALK 
(off-hook) position. 

When making a call in speakerphone mode, the 
number keys being dialed can be heard from the 
speaker. This feature gives an audible feedback to the 
user and assures that each number is being dialed out.

In speakerphone and speaker modes, the TS22A Test 
Set mutes the regular transmitter and receiver to 
prevent acoustic feedback from the speaker. The 
polarity LEDs turn off when the TS22A unit is switched 
from Talk mode to either the speakerphone mode or 
the speaker mode. 

To prolong battery life, the TS22A Test Set will 
automatically shut off the speakerphone or speaker 
after approximately five minutes when there has been 
no signal greater than -30 dBm. Because of the 
automatic shut off feature, this function will have to be 
reactivated every 5 minutes if no signal greater than 
-30 dBm is detected.

bfs03.eps

Talk/
Monitor 
Switch

The (TALK), position establishes an off-hook condition for dialing and talking as a common battery 
telephone. The M (MONITOR) position removes the transmitter from the circuit, and provides a high 
impedance coupling. On the TS22A, the M position provides a high impedance coupling, which 
allows line monitoring without disrupting conversations or signaling. 

MUTE 
button

On the TS22A, pressing the MUTE button turns off the speakerphone microphone for privacy. On 
the TS22, it disables the amplified speaker.

SPEAKER 
Button

This button controls the speakerphone (TS22A only) and Monitor speaker sound levels. See “TS22 
Amplified Speaker” and “TS22A Speakerphone and Speaker Monitor Modes”.

Summary of Contents for TS 19

















Reviews: