background image

Electrical Tester

Maintenance

11

Maintenance

If the Product is used appropriately it does not require special maintenance or repair. See 

www.fluke.com

 

for locations and contact 

information of Fluke Service Centers worldwide.

How to Clean

W

 Caution

For safe operation and maintenance, clean the case with a damp cloth and detergent. Do not use abrasives or 
solvents.

If the Product is dirty, wipe it off carefully with a damp cloth (without cleaning agents). Mild soap may be used.

Battery Replacement

W

 Caution

For safe operation and maintenance of the Product:

Remove batteries to prevent battery leakage and damage to the Product if it is not used for an extended period.

Repair the Product before use if the battery leaks.

Be sure that the battery polarity is correct to prevent battery leakage.

The Product has two AA (IEC LR6) alkaline batteries.

To replace the batteries:

1.

Remove the battery door screw. See Figure 2.

Figure 2. Battery Replacement

2.

Remove the battery door.

3.

Replace the batteries.

4.

Attach the battery door and battery door screw. Do not overtighten the screw.

2 AA

Do not
overtighten
screw

Summary of Contents for T6-1000

















Reviews: