manualshive.com logo in svg

Fluke 9009, User Manual

Share
Download
Fluke 9009 User Manual Download Page 4

9009

User’s Guide

ii

Calibration Parameters ......................................................................... 14

R0 ...................................................................................................... 15
ALPHA ............................................................................................... 15
DELTA ............................................................................................... 15
BETA (Low Temp Only) ..................................................................... 15

Digital Communication Interface ............................................................... 15
Serial Communications ............................................................................. 15

Wiring ................................................................................................... 16
Serial Operation.................................................................................... 16

Interface Commands ................................................................................. 17
Calibrate a Single Probe ........................................................................... 19

Calibrator Characteristics ..................................................................... 20

Stabilization and Accuracy................................................................. 20

Calibration ................................................................................................. 20
Calibration Points ...................................................................................... 20
Calibration Procedure................................................................................ 21

Compute DELTA................................................................................... 21
Compute R0 & ALPHA ......................................................................... 22
Compute BETA (Cold Side Only) ......................................................... 22
Accuracy and Repeatability .................................................................. 23

Maintenance.............................................................................................. 23
Troubleshooting Problems, Possible Causes, and Solutions.................... 23

Summary of Contents for 9009































Reviews:

No comments

Brands by name

Popular brands

Load more brands