Fluke 85RF II Instruction Sheet Download Page 3

 English  

Page 

 

 

Operation 

To operate the 85RF II Probe: 

1. Connect the Probe output to a compatible voltmeter with 

an applicable shunt (if necessary.) The Probe’s output low 
must be connected to voltmeter low. 

2. Set a voltage range (1 V dc reading for each 1 V rms 

Probe input). 

3. Connect the input low (clip lead or tip shield) to earth 

ground. 

WX

Warning 

Input low is intended to be connected to earth 
ground. To prevent electrical shock, input low 
(clip lead or tip shield) must be connected to 
potentials of less than 30 V ac, 42 V peak, or  
60 V dc.  

Frequency Measurements 

Frequencies less than 100 MHz 

To measure frequencies less than 100 MHz: 
1. Ground the 4-inch clip lead supplied with the Probe. 
2. Touch the Probe tip to the circuit under test. 

Frequencies greater than 100 MHz 

To measure frequencies greater than 100 MHz: 

1. Ground the 4-inch clip lead supplied with the Probe. 
2. Touch the Probe tip to the circuit under test. 

Note 

Measurements above 100 MHz must be made with 
minimum cable lengths and a terminated 50 

e

 system. 

One inch or less of non-terminated coaxial cable (such as 
a BNC adapter and 50 

e

 termination) is required for 

measurements up to 300 MHz. 

Frequencies greater than 300 MHz 

To measure frequencies greater than 300 MHz: 

1. Ground the 4-inch clip lead supplied with the Probe. 
2. Touch the Probe tip to the circuit under test. 

Note 

Measurements above 300 MHz must have the Probe tip 
and tip shield (input high and low) touch the circuit under 
test to realize the rated accuracy of the Probe. Lead 
lengths less than 1-inch can cause substantial errors.

 

 

Summary of Contents for 85RF II







Reviews: